Prescaler:分频系数Time Quanta in Bit Segment 1:时间段1(配置为9标识9个时间单元)Time Quanta in Bit Segment 2:时间段2ReSynchronization Jump Width:重新同步跳跃宽度TS1=8、TS2=7、BRP=3,波特率 = 36000 / [( 9 + 8 + 1 ) * 4] = 500KbpsBasic Parameters:基本参数 Time Triggered Communication Mo...
第二个主要的部分Basic parameters 主要是一些模式的使能,根据需要选择就可以了,主要和你的应用相关,这里就不做介绍了,因为小编也没细致的去分析每个参数对应的具体区别 第三个主要部分Advanced Paramaters 这个是用来设置CAN的模式,一般来说CAN可以分为四个模式,如这一项参数选项所示 正常模式 - 正常的收发CAN消息 ...
如果没有shadow register,或者preload register和shadow register是直通的,即软件更新preload register时,同时更新了shadow register,因为软件不可能在一个相同的时刻同时更新多个寄存器,结果造成多个通道的时序不能同步,如果再加上其它因素(例如中断),多个通道的时序关系有可能是不可预知的。 Trigger Output Parameters : 触...
The ST-LINK/V3 is an in-circuit debugger for the STM8 and STM32 microcontrollers. Most of the time it is embedded on the board. If not you can use theSTLinks-V3miniorSTLinks-V3SETstandalone devices. STM32 Basics for MCU Edit
* * @returns a connection handle that can be used to abort the client * by calling @ref lwiperf_abort() */ void* lwiperf_start_tcp_client(const ip_addr_t* remote_addr, u16_t remote_port, enum lwiperf_client_type type, lwiperf_report_fn report_fn, void* report_arg)...
² Basic Parameters Transfer Mode 设置为Memory to Memory Color Mode 设置为RGB565 Output offset = 0 ² Foreground layer Configuration 所有项保持不变。 n Multimedia->DMA2D->Configuration->NVIC Settings DMA2D global interruptEnabled(必选)且Preemption Priority设置为5,这个在System Core->NVIC->Configurat...
函数 CAN_ITConfig 函数名 CAN_ITConfig 函数原形 void CAN_ITConfig(u32 CAN_IT, FunctionalState NewState) 功能描述 使能或者失能指定的 CAN 中断 输入参数 1 CAN_IT:待使能或者失能的 CAN 中断 参阅 Section:CAN_IT 查阅更多该参数允许取值范围 输入参数 2 NewState:CAN 中断的新状态 这个参数可以取:ENABLE...
CAN Generic Driver 118 6.1 CAN Firmware driver registers structures 118 6.1.1 CAN_InitTypeDef 118 6.1.2 CanTxMsgTypeDef 118 6.1.3 CanRxMsgTypeDef 119 6.1.4 CAN_HandleTypeDef 120 6.2 CAN Firmware driver API description 120 6.2.1 How to use this driver 120 6.2.2 Initialization and de-...
安装完成后进行组件下载,把Basic Setup里面的组件全部勾选(也可也去掉不需要的语言编译器比如Objective-C)。 配置系统的环境变量,在Path环境变量里面添加一条,指向MinGW的bin文件夹: 配置环境变量 随后打开终端(或者cmd),如果已经打开,可以尝试关闭再打开
STM32 devices.If users want to see energy profiles and visualize the current draw, they must use STM32CubeMonitor-Power. However, STM32CubeProgrammer will serve as an interface for all debug features. It can also work with all the probe’s interfaces, such as SPI, UART, I2C, and CAN. ...