步骤三:将端口组的模式设置为active 最后,我们需要将端口组的模式设置为active。通过使用kubectl patch命令可以轻松地更新现有的端口组,将其模式设置为active。 ```bash kubectl patch portgroups my-port-group -p '{"spec":{"mode":"active"}}' ``` 通过以上步骤,你已经成功实现了“port-group 1 mode acti...
#internet e0/0/1-2 Port-group 1 mode active Internet port-channel 1 Switchport mode trunk Sw3 Port-group 1 Internet e0/0/1-2(进入端口0/0/1-2) Port-group 1 mode on/___/passive (手动/主动/被动)(将端口加入链路聚合组并选择模式) Internet port-channel 1(进入链路聚合组1) Switchport...
Note: After the delete request and response, the Active Sessions count stats in the output of "show load-balance port-group stats all" command will be cleared only after 4 minutes approximately. # show load-balance port-group stats all Deletes a specified port group. (config) # no port...
Use the add and manage hosts wizard in template mode to migrate physical uplinks to the LAG on multiple hosts simultaneously: reassign uplinks on template host, then apply configuration to desired hosts. Set the LAG to the active state for the desired portgroups by moving it to the active c...
建议使用 lacp协议,mode为active 该模式的一端手工指定物理成员端口的双工,速度,trunk模式等。然后手动建立port-channel 对端的物理端口,手动加入到channel-group 中,对端会主动发送lacp data unit数据单元,如果 发现物理成员端口有速度双工,truunk, nativevlan 的不匹配,则会终止eherchannel,防止2层 环路 ...
Details about the virtual interface.ovs_hybrid_plugspecifies whether the OVS/bridge hybrid mode is used. binding:vif_type String Interface type of the port. The value can beovs,hw_veb, or others. This is an extended attribute. Constraints: This parameter is visible only to administrators. ...
(4) 配置中间设备Device C Device C作为一台中间设备需要支持LACP协议扩展功能,用来转发、处理LACP协议报文,协助Device A和Device B进行多Active检测。从节约成本的角度考虑,使用一台支持LACP协议扩展功能的交换机即可。 # 创建一个动态聚合接口。 代码语言:javascript ...
Router# show vtemplate Virtual access subinterface creation is globally enabled Active Active Subint Pre-clone Pre-clone Interface Interface Subinterface Capable Available Limit Type --- --- --- --- --- --- Vt1 0 0 Yes -- -- Serial Vt2 0 0 Yes -- -- Serial Vt4 0 0 Yes -- ...
1.1.9 lacp mode lacp mode passive命令用来配置端口的LACP工作模式为PASSIVE。 undo lacp mode命令用来恢复缺省情况。 【命令】 lacp mode passive undo lacp mode 【缺省情况】 端口的LACP工作模式为ACTIVE。 【视图】 三层以太网接口视图 【缺省用户角色】 network-admin 【使用指导】 执行本命令后,只有在当前端口...
TCP Server Mode Activates VSP as a TCP/IP server. The driver then behaves as a TCP Client/Server device - this means that the first party to receive any data switches over to Client mode and establishes the connection. In the TCP server mode, IP address is automatically preset to 0.0.0.0...