步骤三:将端口组的模式设置为active 最后,我们需要将端口组的模式设置为active。通过使用kubectl patch命令可以轻松地更新现有的端口组,将其模式设置为active。 ```bash kubectl patch portgroups my-port-group -p '{"spec":{"mode":"active"}}' ``` 通过以上步骤,你已经成功实现了“port-group 1 mode acti...
#internet e0/0/1-2 Port-group 1 mode active Internet port-channel 1 Switchport mode trunk Sw3 Port-group 1 Internet e0/0/1-2(进入端口0/0/1-2) Port-group 1 mode on/___/passive (手动/主动/被动)(将端口加入链路聚合组并选择模式) Internet port-channel 1(进入链路聚合组1) Switchport...
Note: After the delete request and response, the Active Sessions count stats in the output of "show load-balance port-group stats all" command will be cleared only after 4 minutes approximately. # show load-balance port-group stats all Deletes a specified port group. (config) # no port...
默认的 mode是 on,协议是pagp。 该模式下,端口手动配置,强制成员成为etherchannel,即使对端出现问题,用show ether summ 命令依然可以看到强制启动的聚合端口 该模式不会向对端发送 paglp 数据单元,不会协商任何该协议的参数 建议使用 lacp协议,mode为active 该模式的一端手工指定物理成员端口的双工,速度,trunk模式等...
!Time: Sat Jan 6 00:37:20 2001 version 6.0(2)U6(10) interface Ethernet1/2 switchport access vlan 10 channel-group 2 mode active From the output we can see that the interface is currently a switchport in mode access and with vlan 10 configured. It also shows that this...
Device C作为一台中间设备需要支持LACP协议扩展功能,用来转发、处理LACP协议报文,协助Device A和Device B进行多Active检测。从节约成本的角度考虑,使用一台支持LACP协议扩展功能的交换机即可。 # 创建一个动态聚合接口。 代码语言:javascript 复制 <DeviceC>system-view[DeviceC]interfacebridge-aggregation2[DeviceC-Bridg...
Router# show vtemplate Virtual access subinterface creation is globally enabled Active Active Subint Pre-clone Pre-clone Interface Interface Subinterface Capable Available Limit Type --- --- --- --- --- --- Vt1 0 0 Yes -- -- Serial Vt2 0 0 Yes -- -- Serial Vt4 0 0 Yes -- ...
1.1.9 lacp mode lacp mode passive命令用来配置端口的LACP工作模式为PASSIVE。 undo lacp mode命令用来恢复缺省情况。 【命令】 lacp mode passive undo lacp mode 【缺省情况】 端口的LACP工作模式为ACTIVE。 【视图】 三层以太网接口视图 【缺省用户角色】 network-admin 【使用指导】 执行本命令后,只有在当前端口...
Remote port setup– sends control information to the remote port according to VSP settings on your PC. If your terminal software (e.g. Hyperterminal) changes the baudrate to 19200Bd and this feature is active, the VSP driver sends a NVT command (according to the RFC2217 standard) to the...
Switch(config-if)#channel-group 10 mode ? active Enable LACP unconditionally auto Enable PAgP only if a PAgP device is detected desirable Enable PAgP unconditionally on Enable Etherchannel only passive Enable LACP only if a LACP device is detected ...