链路聚合2. 静态LACP汇聚的配置交换机SWA的配置如下:SWAlink-aggregation group 1 mode staticSWAinteface Ethernet 1/0/1SWA-Ethernet1/0/1undo loopback-detection enableSWA-Ethernet1/0/1port link-aggregation group 1SWA-Ethernet1/0/1quitSWA-Ethernet1/0/ 10、2undo loopback-detection enableSWA-...
[Sysname] link-aggregation group 22 mode manual | static （manual手工聚合组，static静态LACP聚合组）#创建并配置链路聚合组 1，配置模式为manual，服务类型为tunnel。 <Sysname> system-view [Sysname] link-aggregation group 1 mode manual [Sysname] link-aggregation group 1 service-type tunnel # 将一个二...
[Sysname] link-aggregation group 1 mode static # Add Ethernet 1/0/1 through Ethernet 1/0/3 to aggregation group 1. [Sysname] interface Ethernet 1/0/1 [Sysname-Ethernet1/0/1] port link-aggregation group 1 [Sysname-Ethernet1/0/1] quit ...
link-aggregation mode dynamic// 配置聚合组工作在动态聚合模式下 缺省情况下,聚合组工作在静态聚合模式下 interface interface-type interface-number// 进入二层以太网接口视图 port link-aggregation group { group-id [ force ] | auto [ group-id ] }// 将二层以太网接口加入聚合组 指定auto参数时,会开启...
[DeviceA] link-aggregation group 1 mode static # Add ports Ethernet 1/0/1 through Ethernet 1/0/3 to the group. [DeviceA] interface ethernet 1/0/1 [DeviceA-Ethernet1/0/1] port link-aggregation group 1 [DeviceA-Ethernet1/0/1] interface ethernet 1/0/2 ...
多选题在交换机SWA 上执行display 命令后,交换机输出如下:<Switch>display link-aggregation summaryAggregation Interface Type:BAGG -- Bridge-Aggregation, RAGG -- Route-AggregationAggregation Mode: S -- Static, D -- DynamicLoadsharing Type: Shar -- Loadsharing, NonS -- Non-LoadsharingActor System ID...
1,链路聚合 link-aggregation# 创建聚合组号为 22 的 手工 | 静态 聚合组,<Sysname> system-viewSysname link-aggregation group 22 mode manual | static(manual手工聚合组,static静态LACP聚合组)#创建并配置链路聚合组1,配置模式为 manual,服务类型为tunnel。<Sysname> system-viewSysname link-aggregation group ...
<Base> display trunkmembership eth-trunk 1 Trunk ID: 1 used status: VALID TYPE: ethernet Working Mode : Static Number Of Ports in Trunk = 3 Number Of UP Ports in Trunk = 0 operate status: down Interface GigabitEthernet0/0/1, valid, operate down, weight=1 Interface GigabitEthernet0/0/...
在交换机SW 上执行display 命令后,交换机输出如下:<Switch>display link-aggregation summaryggregation Interface Type:GG -- ridge-ggregation, RGG -- Route-ggregationggregation Mode: S -- Static, -- ynamicLoadsharing Type: Shar -- Loadsharing, NonS -- Non-L
在此只对手工汇聚和静态LACP汇聚进行介绍，由于动态LACP汇聚由系统自动进行端口的添加和删除，实际应用较少，在此不做介绍。具体涉及到的配置命令如下：[H3C]link-aggregation group agg-id mode[manual|static][H3C]interface interface-type interface-number [H3C-Ethernet1/0/1]port link-aggregation group agg-id...