链路聚合2. 静态LACP汇聚的配置交换机SWA的配置如下:SWAlink-aggregation group 1 mode staticSWAinteface Ethernet 1/0/1SWA-Ethernet1/0/1undo loopback-detection enableSWA-Ethernet1/0/1port link-aggregation group 1SWA-Ethernet1/0/1quitSWA-Ethernet1/0/ 10、2undo loopback-detection enableSWA-...
lacp priority 0 #配置LACP系统优先级 mode lacp-static #选择链路聚合模式 trunkport GigabitEthernet 0/0/1 to 0/0/2 #可以直接在聚合口内直接加入端口 max active-linknumber 2 #最大活动链路 [GigabitEthernet0/0/1]lacp priority 1 #接口优先级 lacp preempt enable #开启抢占 lacp preempt delay 20 #...
link-aggregation 1，链路聚合link-aggregation # 创建聚合组号为22 的 手工 | 静态 聚合组，<Sysname> system-view [Sysname] link-aggregation group 22 mode manual | static （manual手工聚合组，static静态LACP聚合组）#创建并配置链路聚合组 1，配置模式为manual，服务类型为tunnel。 <Sysname> system-view [...
Aggregate Interface: Bridge-Aggregation1 Aggregation Mode: Static LoadsharingType: Shar Management VLANs: None PortStatus Priority Oper-Key GE1/0/1(R) S327681 GE1/0/2S327681 GE1/0/3S327681 以上信息表明,聚合组1为负载分担类型的二层静态聚合组,包含有三个选中端口。 16.2 二层动态聚合配置举例 ...
mode lacp-static The Eth-Trunk is configured to work in static LACP mode. By default, an Eth-Trunk works in manual load balancing mode. If the Eth-Trunk working mode is set to static LACP on the local device, you must set the Eth-Trunk working mode to static LACP on the remote devic...
mode lacp-static The Eth-Trunk is configured to work in static LACP mode. By default, an Eth-Trunk works in manual load balancing mode. If the Eth-Trunk working mode is set to static LACP on the local device, you must set the Eth-Trunk working mode to static LACP on the remote devic...
在交换机SWA 上执行display 命令后,交换机输出如下: display link-aggregation summary Aggregation Interface Type: BAGG -- Bridge-Aggregation, RAGG -- Route-Aggregation Aggregation Mode: S -- Static, D -- Dynamic Loadsharing Type: Shar --...
在交换机SWA上执行 display命令后,交换机输出如下: display link-aggregation summary Aggregation Interface Type: BAGG -- Bridge-Aggregation, RAGG -- Route-Aggregation Aggregation Mode: S -- Static, D -- Dynamic Loadsharing Type: Shar -- Loadsharing, NonS -- Non-LoadshA.聚合组的类型是静态聚合B...
1,链路聚合 link-aggregation# 创建聚合组号为 22 的 手工 | 静态 聚合组,<Sysname> system-viewSysname link-aggregation group 22 mode manual | static(manual手工聚合组,static静态LACP聚合组)#创建并配置链路聚合组1,配置模式为 manual,服务类型为tunnel。<Sysname> system-viewSysname link-aggregation group ...
多选题在交换机SWA 上执行display 命令后,交换机输出如下:<Switch>display link-aggregation summaryAggregation Interface Type:BAGG -- Bridge-Aggregation, RAGG -- Route-AggregationAggregation Mode: S -- Static, D -- DynamicLoadsharing Type: Shar -- Loadsharing, NonS -- Non-LoadsharingActor System ID...