link aggregation mode dynamic 链路聚合模式动态 不明白可以追问我，满意的话请点击【采纳】
Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation, D -- Synchronization, E -- Collecting, F -- Distributing, G -- Defaulted, H -- Expired Aggregate Interface: Route-Aggregation1 Aggregation Mode: Static Loadsharing Type: Shar Port Status Priority Oper-Key --- GE1/0/1...
link-aggregation load-sharing mode dynamic { eligible [ flowlet-gap-time flowlet-gap-time ] | fixed | spray } 缺省情况下,聚合组内采用的聚合静态负载分担类型 11.3 配置缺省聚合负载分担时忽略的字段 当聚合组采用缺省的负载分担类型进行负载分担时,如果负载分担不均匀,用户可以配置本功能忽略报文中的某些字...
三层链路聚合配置 interface route-aggregation 2 ip address 192.168.1.1 255.255.255.0 link-aggregation global load-sharing mode destination-ip #ip地址进行负载分担 link-aggregation mode dynamic #动态聚合模式 interface range g0/0/0 to g0/0/1 lacp mode passive port link-aggregatio group 2...
link-aggregation mode dynamic 组网及组网描述: 2022-10-21提问 举报 (0) 2 个回答 按时间 按赞数 IT钟点工 这是动态聚合 2022-10-21回答 评论(0) 举报 (0) zhiliao_sEUyB 这是配置聚合模式为动态模式。 聚合接口视图下的命令 2022-10-21回答 评论(0) 举报 (0) 编辑答案分享...
Aggregation Mode 聚合组的工作模式: · Static:表示静态聚合 · Dynamic:表示动态聚合 1.1.6 interface route-aggregation interface route-aggregation命令用来创建三层聚合接口,并进入三层聚合接口视图。如果指定的三层聚合接口已经存在,则直接进入该三层聚合接口视图。 undo interface route-aggregation命令用来删除三层聚合...
link-aggregation mode dynamic 配置连接Device D的以太网链路聚合组工作在动态聚合模式 - port m-lag group 1 port m-lag group 1 配置聚合接口加入M-LAG组 - port link-type trunk port link-type trunk 配置二层聚合接口为Trunk端口 - undo port trunk permit vlan 1 undo port trunk permit vlan...
[SwitchA-Bridge-Aggregation1]link-aggregation mode dynamic 2.进入端口G1/0/1 [SwitchA]interface gigabitethernet1/0/1 3.参与端口汇聚的端口设置成全双工模式 [SwitchA-GigabitEthernet1/0/1]duplex full 4.参与端口汇聚的端口工作速率设置一致 [SwitchA-GigabitEthernet1/0/1]speed 1000 ...
配置完成后,在交换机SWA上执行display link-aggregation summary命令显示结果如下: SWAdisplay link-aggregation summaryAggregati on In terface Type:BAGG - Bridge-Aggregation, RAGG - Route-AggregationAggregation Mode: S - Static, D - DynamicLoadsharing Type: Shar- Loadsharing, NonS - Non-Loadsharing...
Aggregation Interface Type: BAGG -- Bridge-Aggregation, RAGG -- Route-Aggregation Aggregation Mode: S -- Static, D -- Dynamic Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing Actor System ID: 0x8000, 000f-e2ff-0001 AGG AGG Partner ID Select Unselect Share Interface Mode ...