输入捕获有 ① Input Capture direct mode和 ② Input Capture indirect mode两种模式可选,但是在没有通道 选择 直接模式输入捕获时,非直接模式的输入捕获是不可选择的,这个也很好理解,直接模式输入捕获会将捕获通道设置到某一个具体的引脚上,而非直接模式的输入捕获不会将捕获通道设置到某一个具体的引脚上,而是使用...
点击TIM3,选择内部时钟(Internal Clock),配置通道1为直接输入捕获模式(Input Capture direct mode) 配置输入捕获的详细参数,首先先配置定时器为72MHz分配,即1us计数一次,每次计数值加1,计数上限设为最大65535,配置如下: 然后配置上升沿触发(Rising Edge),不分频(No division),滤波器的值为0不滤波 滤波器就是输入...
首先新建工程后,配置系统时钟为48MHz(参考之前的文章STM32CubeMX之GPIO的使用)。以TIM1为例,使能TIM1的时钟源为Internal Clock(即48MHz系统时钟),设置通道1为Input Capture direct mode,可以看到对应到PA8引脚自动被设置为TIM1_CH1功能。定时器基本参数的配置参考STM32CubeMx之TIM定时中...
TRGO Parameters(触发输出):不使能在定时器的定时时间到达的时候输出一个信号(如:定时器更新产生TRGO信号来触发ADC的同步转换) Input Capture Channel 1(输入捕获通道1) Polarity Selection:Rising Edge(上升沿捕获) IC Selection:Direct默认 Prescaler Division Ratio:No division默认 Input Filter(4 bits calue)(滤波...
Input Capture direct mode:输入直接捕获模式 Input Capture indirect mode:输入间接捕获模式 Input Capture triggered by TRC:TRC触发输入捕获 Output Compare No Output:输出比较无输出 Output Compare CH1:输出比较CH1 PWM Generation No Output:PWM生成无输出 ...
工程使用CubeMX创建,使用VS Code编程,单片机为STM32F103VCT6。首先配置时钟,下载方式,开启USART以方便调试,这里就不具体展示了。开启某个定时器的输入捕获【Input Capture direct mode】预分频系数设为(72-1),开启捕获中断【TIM1 capture compare interrupt】优先级最好高一些(默认为0 单片机 嵌入式 NEC单片机 ...
顶部Pinout & Configuration→Timers→TIM3→紧靠的右侧TIM3 Mode and Configuration→Channel1选择Input Capture direct mode→下侧Configuration→Parameter Settings→Counter Settings→Counter Period(ARR)设置为0xffff→NVIC Settings→TIM3 global interrupt打勾。
* @param xSize: Buffer width * @param ColorMode: Input color mode * @retval None */static void LCD_LL_ConvertLineToARGB8888(void *pSrc, void *pDst){ /* Enable DMA2D clock */ __DMA2D_CLK_ENABLE();/* Configure the DMA2D Mode, Color Mode and output offset */ ...
waveform mode 267 23.2.2 How to use this driver 268 23.2.3 Initialization and Time Base Configuration functions 271 23.2.4 Simple time base mode functions 272 23.2.5 Simple output compare functions 272 23.2.6 Simple PWM output functions 272 23.2.7 Simple input capture functions 273 23.2.8 ...
TIM8 capture compare interruptTIM8 capture compare interrupt是捕获比较中断,这个就很好理解了,我们前面通用定时器的实验有介绍到。例如捕获到上升沿/下降沿时会发生捕获中断,计数器的值和比较寄存器的值相等时就会触发中断,关于输出比较我们后面的实验会讲解。