输入捕获有 ① Input Capture direct mode和 ② Input Capture indirect mode两种模式可选,但是在没有通道 选择 直接模式输入捕获时,非直接模式的输入捕获是不可选择的,这个也很好理解,直接模式输入捕获会将捕获通道设置到某一个具体的引脚上,而非直接模式的输入捕获不会将捕获通道设置到某一个具体的引脚上,而是使用...
进入主要操作 顶部Pinout & Configuration→Timers→TIM3→紧靠的右侧TIM3 Mode and Configuration→Channel1选择Input Capture direct mode→下侧Configuration→Parameter Settings→Counter Settings→Counter Period(ARR)设置为0xffff→NVIC Settings→TIM3 global interrupt打勾。 另外我还设置了SPI接口,以便在12864屏幕显示...
点击TIM3,选择内部时钟(Internal Clock),配置通道1为直接输入捕获模式(Input Capture direct mode) 配置输入捕获的详细参数,首先先配置定时器为72MHz分配,即1us计数一次,每次计数值加1,计数上限设为最大65535,配置如下: 然后配置上升沿触发(Rising Edge),不分频(No division),滤波器的值为0不滤波 滤波器就是输入...
后读取此时的定时器值到 TIM5CH1_CAPTURE_VAL 里面,最后设置为上升沿捕获,回到初始 状态。 这样,我们就完成一次高电平捕获了,只要 TIM5CH1_CAPTURE_STA 的第 7 位一直为 1, 那么就不会进行第二次捕获,我们在main函数处理完捕获数据后,将TIM5CH1_CAPTURE_STA 置零,就可以开启第二次捕获。 timer.h 头文件内...
Channel1通道1选择Input Capture direct mode输入捕获模式。 注:TIM5 的通道1对应开发板上 KEY1 的 PA0。 在Parameter Settings进行具体参数配置。 Tclk即内部时钟CK_INT,经过APB1预分频器后分频提供,如果APB1预分频系数等于1,则频率不变,否则频率乘以2,库函数中APB1预分频的系数是2,即PCLK1=36M,如图所以定时...
以TIM1为例,使能TIM1的时钟源为Internal Clock(即48MHz系统时钟),设置通道1为Input Capture direct mode,可以看到对应到PA8引脚自动被设置为TIM1_CH1功能。定时器基本参数的配置参考STM32CubeMx之TIM定时中断,其它具体配置如下图。 STM32的定时器通道可以设置上升沿捕获、下降沿捕获或者上升沿下降沿...
Input Capture direct mode:输入直接捕获模式 Input Capture indirect mode:输入间接捕获模式 Input Capture triggered by TRC:TRC触发输入捕获 Output Compare No Output:输出比较无输出 Output Compare CH1:输出比较CH1 PWM Generation No Output:PWM生成无输出 ...
Enable the Input captureDirect Modeon channel 1. ThePrescaleris set to 90, which will divide the APB2 clock by 90, making the Timer 2 clock =1 MHz. I am leaving theARRto 0xffffffff (Max for 32 bit Timer). Also Enable theInterruptfor the TIM2. This allow the input Capture to trigg...
void InputCapture_RCC_Configuration(void){ /* TIM3 clock enable */ RCC_APB1PeriphClockCmd(RCC_...
channel1 选择 input capture direct mode channel2 选择 input capture indirect mode 下方的设置按照图上所设一样就行最后打开工程,插入如下代码,开启定时器1通道1和通道2的捕获中断/* USER CODE BEGIN 2 */ HAL_TIM_IC_Start_IT(&htim1,TIM_CHANNEL_1); HAL_TIM_IC_Start_IT(&htim1,TIM_CHANNEL_2)...