• 修改代码中的 Flash 绝对地址(这里以 STM32H7 的 CRC_Example 例程为例, 其他情况下有可能要修改更多) o 在 startup_xxx.s 汇编代码里的 sidata o 在 system_xxx.c 里的 SCB->VTOR 以及中断向量表内容 o GOT 对于完整工程,要正确的跳转到应用程序进行执行,还需要由 Bootloade
5. Reset the CRC peripheral through the Reset bit in CRC Control register (CRC_CR). 6. Set the data to the CRC Data register. 7. Read the content of the CRC Data register. 8. Disable the CRC peripheral clock. In firmware package, the CRC_usage example runs the CRC checksum code com...
/** 97. * @brief Used to activate CRC feature inside HAL SPI Driver 98. * Activated (1U): CRC code is compiled within HAL SPI driver 99. * Deactivated (0U): CRC code excluded from HAL SPI driver 100. */ 101. 102. #define USE_SPI_CRC 1U 103. 104. 105. /* Includes ---*/...
uint16_t crc16(uint8_t * frame, uint16_t len ) { unsigned char uchCRCHi = 0xFF ; unsigned char uchCRCLo = 0xFF ; unsigned uIndex ; while (len--) { uIndex = uchCRCHi ^ *frame++ ; uchCRCHi = uchCRCLo ^ auchCRCHi[uIndex] ; uchCRCLo = auchCRCLo[uIndex] ; } retu...
如果没有,执行计算CRC,将芯片中读取数据出来和RAM中加载应用计算输出的CRC值做比较。 执行Uninit函数。 替换BKPT(BreakPoint断点指令)为 B. 死循环指令。 执行RecoverySupportStop,回复支持停止。 执行DebugCoreStop,调试内核停止。 运行应用: 执行失败 执行成功,再执行硬件复位。
说明 这节测试一下STM32+Air724UG实现利用http远程更新STM32程序 我已经把固件文件放在了自己的服务器上 默认使用本人提供的下载路径测试 文件路径: 网站根目录->ota->hardware->STM32Air724BK user_crc.bin: 是固件程序文件. 该固件程序文件并不是直接可以运行的文件 里...111...
SPI配置中设置数据长度为8bit,MSB先输出分频为64分频,则波特率为125KBits/s。其他为默认设置。 Motorla格式,CPOL设置为Low,CPHA设置为第一个边沿。不开启CRC检验,NSS为软件控制。 最后记得初始化一下串口,因为需要测试例程,发送数据到上位机。很简单,这里就不再赘述了,不懂得同学请看: ...
This code however is based on this example and expands it by an data input and a full configuration of the chip. There is another example in my repository wich provides code for the reciever. Apart from the example code by STM (STMicroelectronics/STM32CubeWL/Projects/NUCLEO-WL55JC/Examples...
CRC calculation unit Reset and power management Voltage range: 1.7 V to 3.6 V Separate I/O supply pin (1.65 V to 3.6 V) Power-on/Power-down reset (POR/PDR) Programmable Brownout reset (BOR) Programmable voltage detector (PVD) Low-power modes:Sleep, Stop, Standby, Shutdown ...
= HAL_OK) { return LOADER_FAIL; } HAL_GPIO_TogglePin(GPIOI, GPIO_PIN_8); return LOADER_OK; } /** * Description : * Calculates checksum value of the memory zone * Inputs : * StartAddress : Flash start address * Size : Size (in WORD) * InitVal : Initial CRC value * outputs ...