关联:在设备启动或重置过程中,rst:0xc和boot:0x28是紧密相连的。当设备由于软件内部逻辑触发RTC_SW_CPU_RST复位时,它将以SPI_FAST_FLASH_BOOT模式重新启动。这意味着设备将从SPI闪存中重新加载引导加载程序和应用程序。 影响:这种复位和启动模式的组合通常不会对设备的数据或配置造成持久性影响(除非应用程序在复位...
esp32 的GPIO12/13与4G模块的串口相连,GPIO12为Strapping管脚,上电后由于4G模块的串口的影响,电压为2.5V。对比具体要求: 改变了下拉状态,造成重启。 解决方案: 串口改为 的GPIO14/15后正常。 转:ESP32处于无限重启状态,串口消息rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)-CSDN博客...
rst:0x10 (RTCWDT_RTC_RESET),boot:0x1f (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 I am getting this error in my esp32 devkit v1 How to solve it? I am using arduino IDE for programming the esp32. This error went away after I changed esptool.py params to start ...
I (70) boot.esp32: SPI Mode : DIO I (75) boot.esp32: SPI Flash Size : 4MB I (79) boot: Enabling RNG early entropy source... I (85) boot: Partition Table: I (88) boot: ## Label Usage Type ST Offset Length I (96) boot: 0 nvs WiFi data 01 02 00009000 00004000 I (103...
boot:0x13 (SPI_FAST_FLASH_BOOT)flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)...
esp32 wroom32模块不断重启rst 0xc (SW_CPU_RRESET,boot 0x13(SPI_FAST_FLASH_BOOT) 1 post • Page1of1 月色真美啊啊啊 Posts:1 Joined:Sat Jun 15, 2024 4:18 pm Postby月色真美啊啊啊»Sat Jun 15, 2024 4:28 pm 最近一个项目因为空间有限,所以将硬件从开发板上转移到模块上,程序没问题,因为...
+ rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) + configsip: 0, SPIWP:0xee + clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 + mode:DIO, clock div:2 + load:0x3fff0008,len:4 ...
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)configsip: 0, SPIWP:0xee clk_drv:...
Rebooting... �ESP-ROM:esp32s3-20210327 Build:Mar 27 2021 rst:0xc (RTC_SW_CPU_RST),boot:0x9 (SPI_FAST_FLASH_BOOT) Saved PC:0x40375834 0x40375834: esp_restart_noos at /home/rafal/esp/esp-idf/components/esp_system/port/soc/esp32s3/system_internal.c:151 (discriminator 1) SPIWP:...
I have reviewed the documentation carefully, but when I activate flash encryption and secure boot v2 (rev 3 chip) I get this error. Code:Select all rst:0x1(POWERON_RESET),boot:0x13(SPI_FAST_FLASH_BOOT)invalidheader: 0x3cedda74invalidheader: 0x3cedda74invalidheader: 0x3cedda74invalidheader...