boot:0x13 (spi_fast_flash_boot) 是ESP32 微控制器启动日志中的一个字段,表示设备的启动模式。其中,boot 字段指明了启动配置,而 0x13 是特定的启动模式代码。spi_fast_flash_boot 则表示设备通过 SPI 接口以快速模式从外部 Flash 启动。 2. 描述 spi_fast_flash_boot 在启动过程中
esp32 wroom32模块不断重启rst 0xc (SW_CPU_RRESET,boot 0x13(SPI_FAST_FLASH_BOOT)by 月色真美啊啊啊 » Sat Jun 15, 2024 4:28 pm 最近一个项目因为空间有限,所以将硬件从开发板上转移到模块上,程序没问题,因为核心模块型号是一致的。下载程序成功后就一直报错重启,如图。为了验证是否是模块问题,下载...
7. **SPI Flash问题**：SPI Flash可能存在问题，导致模块无法正常启动。您可以尝试更换SPI Flash或者...
voidsetup() { Serial.begin(115200); } voidloop() { Serial.println("Hello");delay(1000); } Just for testing, and i have this error : Code:Select all rst:0x10(RTCWDT_RTC_RESET),boot:0x13(SPI_FAST_FLASH_BOOT)flashreaderr,1000ets_main.c371etsJun82016 00:22:57 ...
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,len:1044 ...
I have conected the DO pin on D25 of ESP32 pin, pin GND on the GND and VCC pin on 3v3. I tried erase the flash with flash_download_tool_3.8.8 without lucky Thanks.You do not have the required permissions to view the files attached to this post.ulli...
0x1000 -o build/bootloader/bootloader_encrypted.bin build/bootloader/bootloader.bin espsecure.py encrypt_flash_data --keyfile ./key.bin --address 0x8000 -o build/partition_table/partition-table-encrypted.bin build/partition_table/partition-table.bin espsecure.py encrypt_flash_data --keyfile ./...
Hello, I got this error and have been searching for an answer but no luck, and not sure if this's the right place to post the question. Please delete or move it if this's not a valid location. Goal: Loading firmware to my custom board us...
ESP32 烧写microopython后 上电结果反复重启,打印如下: rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57
Re: rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) Postbynicosandller»Mon Jan 30, 2023 3:55 am Hey ! Another Arduino user here. Is there a link we can use to understand how to use ESP-IDF to enable C++ exceptions to keep using Arduino after?