boot:0x13 (spi_fast_flash_boot) 表示ESP32的启动模式。在ESP32等微控制器中,boot 字段指明了设备的启动配置。0x13 是特定的启动模式代码,而 spi_fast_flash_boot 表示设备通过SPI接口以快速模式从外部Flash启动。这是ESP32默认的启动模式之一,允许设备直接从连接的Flash存储器中加载程序
esp32 的GPIO12/13与4G模块的串口相连,GPIO12为Strapping管脚,上电后由于4G模块的串口的影响,电压为2.5V。对比具体要求: 改变了下拉状态,造成重启。 解决方案: 串口改为 的GPIO14/15后正常。 转:ESP32处于无限重启状态,串口消息rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)-CSDN博客...
nodemcu ESP32 刷写 microopython 烧写的过程与ESP8266类似,同样使用了 flash_download_tools 工具进行烧写 烧写过程参照ESP8266烧写 烧写结束后 上电结果反复重启,打印如下 13:43:39.148 -> rst:0x3 (SW_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) 13:43:39.148 -> flash read err, 1000 13:43:39.148 ->...
esp32 wroom32模块不断重启rst 0xc (SW_CPU_RRESET,boot 0x13(SPI_FAST_FLASH_BOOT)by 月色真美啊啊啊 » Sat Jun 15, 2024 4:28 pm 最近一个项目因为空间有限,所以将硬件从开发板上转移到模块上,程序没问题,因为核心模块型号是一致的。下载程序成功后就一直报错重启,如图。为了验证是否是模块问题,下载...
板子是esp32-wroom,烧写后一直提示 rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT...
I tried to push this code to my esp32 wrover : Code:Select all voidsetup() { Serial.begin(115200); } voidloop() { Serial.println("Hello");delay(1000); } Just for testing, and i have this error : Code:Select all rst:0x10(RTCWDT_RTC_RESET),boot:0x13(SPI_FAST_FLASH_BOOT)flash...
espsecure.py generate_flash_encryption_key ./key.bin espefuse.py --port (PORT) burn_key flash_encryption ./key.bin espefuse.py --port (PORT) burn_efuse FLASH_CRYPT_CNT espefuse.py --port (PORT) burn_efuse FLASH_CRYPT_CONFIG 0x0F espsecure.py encrypt_flash_data --keyfile ./key...
ESP-ROM:esp32s3-20210327 Build:Mar 27 2021 rst:0x7 (TG0WDT_SYS_RST),boot:0x8 (SPI_FAST_FLASH_BOOT) Saved PC:0x400454d5 SPIWP:0xee mode:DIO, clock div:2 load:0x3fce3808,len:0x1664 load:0x3c970000,len:0xbb840 ets_loader.c 78 ...
Hardware: Board: ESP32-CAM WROVER MODULE Core Installation/update date: 11/jul/2017 IDE name: ARDUINO 1.8.9 Flash Frequency: 80 MHZ PSRAM enabled: no Upload Speed: 115200 Computer OS: Windows 10 Description: I've got newly ESP-32CAM and ...
ERROR: rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)by hanshasn12345678 » Sun Aug 08, 2021 8:22 pm Hello everyone! I'm beginner with the ESP32, I'm trying show values of a 3 pin Photosensitive sensor with the ESP32 DevKitV1 in the monitor serie but in the moment...