要配置和优化STP、PortFast、Edge和BPDU Guard特性,可以按照以下步骤进行: 全局启用PortFast: plaintext Switch(config)# spanning-tree portfast default 在特定端口上启用PortFast和BPDU Guard: plaintext Switch(config-if)# spanning-tree portfast Switch(config-if)# spanning-tree bpduguard enable 将端口配置为...
百度试题 题目网络管理员输入 spanning-tree portfast bpduguard default 命令。在思科交换机上发出此命令会有什么结果?相关知识点: 试题来源: 解析 如果端口接收到 BPDU,配置了 PortFast 的所有交换机端口将为错误禁用状态。反馈 收藏
网络管理员输入 spanning-tree portfast bpduguard default 命令。 在思科交换机上发出此命令会有什么结果? A、如果端口接收到 BPDU,所有交换机端口将为错误禁用状态。 B、所有 TRUNK 端口可以立即连接到网络,而不是等待融合。 C、如果端口接收到 BPDU,配置了 PortFast 的所有交换机端口将为错误禁用状态。 D、接收...
A network administrator enters the spanning-tree portfast bpduguard default command. What is the result of this command being issued on a Cisco switch? A. Any switch port will be error-disabled if it receives a BPDU. B. Any switch port that has been configured with PortFast will be error-...
spanning-tree portfast edge bpdufilter default spanning-tree portfast edge bpduguard default spanning-tree portfast edge [trunk] Information About Optional Spanning-Tree Features The following sections provide information about Optional Spanning-Tree f...
SW13# show spanning-tree summary Switch is inpvstmode Root bridgefor: VLAN0001, VLAN0010, VLAN0020 Extended system ID is enabled PortfastDefault is disabled Portfast Edge BPDU Guard Default is disabled Portfast Edge BPDU Filter Default is disabled ...
spanning-tree vlan 10 priority 28672 如果配置优先级为0则最大可能性成为主根 SW1(config)#spanning-tree vlan 10 priority 0 SW2(config)#spanning-tree vlan 1 priority 0 根端口选举: 接收最优的BPDU (1、Cost 2、BID 3、Port ID ) 2、Vlan10 中的sw2的E1/1变为转发状态 ...
当完成上述的配置后,可以通过在交换机S1上执行show spanning-tree如图所示,可以看出当前的portfast配置生效,因为该交换机的所有端口都是Edge(边缘端口),从某种意义上讲,这里的边缘端口就是portfast。 在交换机S1上通过全局命令配置BPDUGuard功能: S1(config)#spanning-treeportfast bpduguard default *在所有portfast端口...
SW13# show spanning-tree summary Switch is inpvstmode Root bridgefor: VLAN0001, VLAN0010, VLAN0020 Extended system ID is enabled PortfastDefault is disabled Portfast Edge BPDU Guard Default is disabled Portfast Edge BPDU Filter Default is disabled ...
起用portfast往往是因为一些应用的要求,cisco是建议将符合条件的port设置成portfast的. PS: 将SWITCH的端口设置为spanning-tree portfast后,如果这个端口接到其他SWITCH或者HUB上就可能造成环路问题。加上spanning-tree bpduguard enable之后,当这个端口在收到BPDU包后就会进入errdisable状态,从而避免环路。