Switch(config-if)# spanning-tree portfast edge 监控和故障排除: 使用show spanning-tree命令查看STP的状态和配置。 使用show spanning-tree interface <interface-name> detail命令查看特定端口的STP详细信息。 如果端口被BPDU Guard置于err-disable状态,可以使用errdisable recovery cause bpduguard命令自动恢复...
激活端口之前,让端口连接至等待侦听和学习状态的计算机毫无意义。 结合使用PortFast和BPDU-Guard是最佳实践,那样如果通过该接口收到BPDU,它可以防御性地关闭端口。 激活这项功能的思科IOS全局命令如下: Core-Sw1(config)# spanning-tree portfast edge bpduguard 激活这项功能的思科IOS接口配置命令如下: Core-Sw1(confi...
Bpdugard: SW1(config)#spanning-tree portfast defaul ---全局下针对Portfast终端 SW1(config)#spanning-tree portfast edge bpduguard SW1(config)#spanning-tree portfast defaul ---全局下针对Portfast终端 SW1(config)#no spanning-tree portfast edge bpduguard SW1(config)#interface range ethernet 1/0-1 ...
Extended system ID is enabled PortfastDefault is disabled Portfast Edge BPDU Guard Default is disabled Portfast Edge BPDU Filter Default is disabled Loopguard Default is disabled PVST Simulation Default is enabled but inactive inpvstmode Bridge Assurance is enabled but inactive inpvstmode Ether Channel ...
Hi All, I'm confused as to why we would use the command "portfast" on a trunk link. May be i was wrong when i learnt that "portfast" is used only on Access ports which has BPDU guard enabled. Thank you! Sagar HiremathEnterprise...
Enable PortFast on a trunk port that is connected to a single workstation, switch, or server. set spantree portfast mod_num/port_num enable trunk Note https://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifIf you enter the set spantree portfast command on a trunk port without ...
起用portfast往往是因为一些应用的要求,cisco是建议将符合条件的port设置成portfast的. PS: 将SWITCH的端口设置为spanning-tree portfast后,如果这个端口接到其他SWITCH或者HUB上就可能造成环路问题。加上spanning-tree bpduguard enable之后,当这个端口在收到BPDU包后就会进入errdisable状态,从而避免环路。
51CTO博客已为您找到关于spanning-tree portfast edge的相关内容,包含IT学习相关文档代码介绍、相关教程视频课程,以及spanning-tree portfast edge问答内容。更多spanning-tree portfast edge相关解答可以来51CTO博客参与分享和学习,帮助广大IT技术人实现成长和进步。
意思是直接从BLK跳到了FWD,完全不用再进行计算。这就是portfast 注意:portfast,是用在连接终端的接口上的,(PC,SERVER,只要不是交换机就行) 配置命令 sw1(config)#spanning-tree portfast edge default 在全局配置模式下开启,则针对此设备上的所有access口进行配置, ...
5、边缘端口edge port。 它基本对应【PortFast】属性,连接终端设备,直接进行到Forwarding状态。不会产生Top_change BPDU。如果该端口接收 BPDU 的边缘端口会立即失去边缘端口状态并成为正常的生成树端口。 回顾 802.1D hello 默认2s Forward_delay默认15秒, max__aging 20秒。