将端口配置为Edge Port(通常与PortFast结合使用): plaintext Switch(config-if)# spanning-tree portfast edge 监控和故障排除: 使用show spanning-tree命令查看STP的状态和配置。 使用show spanning-tree interface <interface-name> detail命令查看特定端口的STP详细信息。 如果端口被BPDU Guard置于err-disable...
Core-Sw1(config)# spanning-tree portfast edge bpduguard 激活这项功能的思科IOS接口配置命令如下: Core-Sw1(config-if)# spanning-tree bpduguard enable 如果交换机已配置好了任何端口信道,那么配置以太网信道保护机制(EtherChannel guard)是个好主意。 激活这项功能的思科IOS全局命令如下: Core-Sw1(config)# ...
SW1(config)#spanning-tree portfast defaul ---全局下针对Portfast终端 SW1(config)#spanning-tree portfast edge bpduguard SW1(config)#spanning-tree portfast defaul ---全局下针对Portfast终端 SW1(config)#no spanning-tree portfast edge bpduguard SW1(config)#interface range ethernet 1/0-1 SW1(config...
PortfastDefault is disabled Portfast Edge BPDU Guard Default is disabled Portfast Edge BPDU Filter Default is disabled Loopguard Default is disabled PVST Simulation Default is enabled but inactive inpvstmode Bridge Assurance is enabled but inactive inpvstmode Ether Channel misconfig guard is enabled Conf...
Enabling PortFast on a Trunk Port Task Command Step 1 Enable PortFast on a trunk port that is connected to a single workstation, switch, or server. set spantree portfast mod_num/port_num enable trunk Note https://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifIf you enter...
Enabling PortFast on a Trunk Port Task Command Step 1 Enable PortFast on a trunk port that is connected to a single workstation, switch, or server. set spantree portfast mod_num/port_num enable trunk Note https://www.cisco.com/c/dam/en/us/td/i/templates/blank.gifIf you enter...
51CTO博客已为您找到关于spanning-tree portfast edge的相关内容,包含IT学习相关文档代码介绍、相关教程视频课程,以及spanning-tree portfast edge问答内容。更多spanning-tree portfast edge相关解答可以来51CTO博客参与分享和学习,帮助广大IT技术人实现成长和进步。
起用portfast往往是因为一些应用的要求,cisco是建议将符合条件的port设置成portfast的. PS: 将SWITCH的端口设置为spanning-tree portfast后,如果这个端口接到其他SWITCH或者HUB上就可能造成环路问题。加上spanning-tree bpduguard enable之后,当这个端口在收到BPDU包后就会进入errdisable状态,从而避免环路。
(portfast,uplinkfast,backbonefast)后面会讲到 而这一切的定义,都是为了更加快速的进行完成收敛。 如下图所示,在一个网络拓扑中有两台汇聚和两台接入, 通常情况下我们是将STP的 根定义在汇聚/核心层的设备上,因为他们有更好的硬件水平,更高的传输速率,更优能性能,这一点是毋庸置疑的。
思路很重要!不同厂商Spanning-tree对接案例思考,朋友们是否经历过客户网络设备替换割接,如果被替换的设备和新设备不是一个厂商,往往在割接准备过程中会暴露出很多棘手的问题。例如,设备厂商往往有大量的私有协议,从而导致了在不同厂商设备之间无法正常互联互通。如果