方法一、复位键恢复出厂设置 复位键,就是指一键将路由器恢复到出厂设置的按钮或小孔,在斐讯K2路由器机身上标注WPS/RESET的按钮即为复位键,如下图所示。 在斐讯K2通电的情况下,用手长按WPS/RESET按键10秒左右的时间,就可以把这台斐讯K2路由器恢复出厂设置了。 注意问题:需要一直按住WPS/RESET按钮10秒左右的时间不...
1. 解释 esp32 rst:0x10 (rtcwdt_rtc_reset) 的含义和可能原因 rst:0x10 (rtcwdt_rtc_reset) 是ESP32启动日志中常见的复位原因表示。这里的 rst 表示复位(Reset),而 0x10 是复位原因的代码。rtcwdt_rtc_reset 指的是由实时时钟看门狗(RTC Watchdog Timer)触发的复位。 可能原因: 软件未按时喂狗:在设备长...
原因分析: 经查是连接4G模块的串口影响。esp32 的GPIO12/13与4G模块的串口相连,GPIO12为Strapping管脚,上电后由于4G模块的串口的影响,电压为2.5V。对比具体要求: 改变了下拉状态,造成重启。 解决方案: 串口改为 的GPIO14/15后正常。 转:ESP32处于无限重启状态,串口消息rst:0x10 (RTCWDT_RTC_RESET),boot:0x33...
软件环境:ESP-IDF v4.3-302-g47b96db-dirty 硬件环境:ESP32_Devkitc_V4开发板 开发环境:linux 问题描述:在idf4.3版本上编译下载后,上电运行时,不断重启,日志打印如下: rst:0x3 (SW_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0...
esp32 wroom32模块不断重启rst 0xc (SW_CPU_RRESET,boot 0x13(SPI_FAST_FLASH_BOOT)by 月色真美啊啊啊 » Sat Jun 15, 2024 4:28 pm 最近一个项目因为空间有限,所以将硬件从开发板上转移到模块上,程序没问题,因为核心模块型号是一致的。下载程序成功后就一直报错重启,如图。为了验证是否是模块问题,下载...
1. **电源问题**：确保您的ESP32模块电源稳定，电压在3.3V左右。不稳定的电源可能导致模块无法正常...
Code:Select all #defineCAMERA_MODEL_AI_THINKER The main settings are correct: Board: AI Thinker ESP32-CAM CPU Frequency: 240MHz (WiFi/BT) Partition scheme: Huge APP (3MB No OTA/1MB SPIFFS) There are 1...3 resets, with one "." in the end (dots are indicators of WiFi connection est...
ESP32,在开发时,在以下代码片中(功能很简单,定时改变PWM的Duty): // A code block while (1) { for (int i = 0; i < 100; i++) { /* code */ // Set duty to 50% ledc_set_duty(LEDC_MODE, LEDC_CHANNEL, i*40); // Update duty to apply the new value ledc_update_duty(LEDC_...
The QT Py ESP32-S3 microcontroller ships running a NeoPixel rainbow swirl example. It's lovely, but you probably had other plans for the board. As you start working with your board, you may want to return to the original code to begin again, or you may find your board gets into a ba...
This problem is mostly related to when you communicated over UART with external device being master and ESP being slave. The fix is simple you need to reset master statemachine if your slave communicating over UART. or Master to provide interface to reset the statemachine at the time of boot...