方法一、复位键恢复出厂设置 复位键,就是指一键将路由器恢复到出厂设置的按钮或小孔,在斐讯K2路由器机身上标注WPS/RESET的按钮即为复位键,如下图所示。 在斐讯K2通电的情况下,用手长按WPS/RESET按键10秒左右的时间,就可以把这台斐讯K2路由器恢复出厂设置了。 注意问题:需要一直按住WPS/RESET按钮10秒左右的时间不...
I unplug the esp32 from my Host computer..then when again powered ON..things wont work. I need to press Reset Button 'EN' on esp32 to get it working... Whats going on ?mikemoy Posts: 641 Joined: Fri Jan 12, 2018 9:10 pm Re: Reset -unplug esp32 IssueQuote...
ESP32的PHY(物理层)复位GPIO引脚编号是GPIO 0。 ESP32的PHY复位通常是通过将特定的GPIO引脚拉低或拉高来实现的。在ESP32中,GPIO 0常用于启动模式选择和PHY复位。当GPIO 0在启动时被拉低时,ESP32会进入下载模式,而如果在运行时将GPIO 0拉低,则可以触发PHY的复位。 需要注意的是,在进行PHY复位时,应确保按照ESP...
原因分析: 经查是连接4G模块的串口影响。esp32 的GPIO12/13与4G模块的串口相连,GPIO12为Strapping管脚,上电后由于4G模块的串口的影响,电压为2.5V。对比具体要求: 改变了下拉状态,造成重启。 解决方案: 串口改为 的GPIO14/15后正常。 转:ESP32处于无限重启状态,串口消息rst:0x10 (RTCWDT_RTC_RESET),boot:0x33...
Check the current capability of your LDO (>500mA), make sure there's at least some capacitance on the power rails close to the ESP32 module if the traces from the power supply to it are of any significant length, and also check that the WiFi antenna doesn't have metal around it....
esp32 wroom32模块不断重启rst 0xc (SW_CPU_RRESET,boot 0x13(SPI_FAST_FLASH_BOOT)by 月色真美啊啊啊 » Sat Jun 15, 2024 4:28 pm 最近一个项目因为空间有限,所以将硬件从开发板上转移到模块上,程序没问题,因为核心模块型号是一致的。下载程序成功后就一直报错重启,如图。为了验证是否是模块问题,下载...
The first few lines do not show up with esp-idf-monitor as the case with a power-on or a reset. My device: ESP32-S3-DevKitC-1 Collaborator fhrbata commented Oct 17, 2024 Hello @mjgci, thank you once again for highlighting this problem and for all your assistance; it is greatly ...
1. **电源问题**：确保您的ESP32模块电源稳定，电压在3.3V左右。不稳定的电源可能导致模块无法正常...
软件环境:ESP-IDF v4.3-302-g47b96db-dirty 硬件环境:ESP32_Devkitc_V4开发板 开发环境:linux 问题描述:在idf4.3版本上编译下载后,上电运行时,不断重启,日志打印如下: rst:0x3 (SW_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0...
Re: RTC reset on deepsleep wakeup - ESP32-C3 Postbyaxellin»Wed Apr 12, 2023 2:46 am Sorry for the late reply and thanks for asking! RTC should not be reset when the chip is woken up by a GPIO from deep-sleep mode. This happens because there is a bug in ESP-IDF code. The ...