1.1.19 port link-aggregation group 1.1.20 reset lacp statistics1 以太网链路聚合 1.1 以太网链路聚合配置命令 1.1.1 display interface display interface命令用来显示聚合接口的相关信息。 【命令】 display interface [ route-aggregation [ interface-number ] ] [ brief [ description | down ] ] 【视图】 ...
想把端口g1/0/49设置成port linkaggregation group1,但是输完命令后提示:can't assgin the port to the aggregation group because its attribute configurations are different than the aggregate interface 组网及组网描述: 设备是接入层交换机 型号 s5130 2022-12-24提问 举报 (0) 4 个回答 按时间 按赞数 ...
betweenthememberportsintheaggregationgrouptoincrease thebandwidth.Atthesametime,dynamicbackupofeachmember portofthesameaggregationgroupenhancesthereliabilityof theconnection. BasedontheIEEE802.3ADstandardLACP(LinkAggregation ControlProtocol,LinkAggregationControlProtocol)isa ...
port link-aggregation group 1 在Kubernetes中实现端口链路汇聚(port link-aggregation)组1(group 1)是一个常见的操作,特别是在需要提高网络带宽和可靠性的场景下。在本文中,我将向你介绍如何通过Kubernetes实现这一操作,以及详细的步骤和代码示例。 ### 步骤概述 要实现端口链路汇聚组1,我们需要按照以下步骤进行操作...
步骤1 将原来已加入的聚合组的端口退出 步骤2 删除聚合组 命令参考如下，（具体的端口号，聚合组 请根据你的实际情况修改）：interface GigabitEthernet 0/8 undo port link-aggregation group 1 quit undo link-aggregation group 1
[SwitchA-GigabitEthernet1/0/3]port link-aggregation group 2 12.负荷分担基于源MAC和目的MAC [SwitchA]link-aggregation load-sharing mode source-mac 13.端口G1/0/4与端口G1/0/3的配置一致 二、 SwitchB的配置顺序和配置内容同SwitchA的G1/0/1 ...
因为后边不用加“1”，一个端口只能属于一个聚合组，所以删除的时候，敲到group就可以了，不用跟后边...
[DeviceA] interface gigabitethernet 1/4/0/2 [DeviceA-GigabitEthernet1/4/0/2] port link-aggregation group 2 [DeviceA-GigabitEthernet1/4/0/2] quit [DeviceA] interface gigabitethernet 2/4/0/2 [DeviceA-GigabitEthernet2/4/0/2] port link-aggregation group 2 (4) 配置中间设备Device C Devi...
23 converged into a link. Hand pooling: Configuration of the first switch: [H3CA] link - aggregation group 10 mode manual [H3CA] interface Ethernet 1/0/24 H3CA - Ethernet1/0/24 port link aggregation group - 10 Can not specify a loopback - detection enable port as aggregation group ...
[SW1-Bridge-Aggregation2]port trunk permit vlan all 其他设备配置捆绑 [S5820] int Bridge-Aggregation 2 [S5820]int ran ten 1/0/50 ten 1/0/51 [S5820-if-range]port link-aggregation group 2 [S5820]int Bridge-Aggregation 2 [S5820-Bridge-Aggregation2]port link-type trunk ...