1.1.3 display link-aggregation member-port display link-aggregation member-port命令用来显示成员端口上链路聚合的详细信息。 【命令】 display link-aggregation member-port [ interface-list | auto ] 【视图】 任意视图 【缺省用户角色】 network-admin network-operator 【参数】 interface-list:成员端口列表,表...
[sw1-GigabitEthernet1/0/2]portlink-aggregation group 1 将该接口加入聚合组中 [sw1-GigabitEthernet1/0/2]qu [sw1]interfaceBridge-Aggregation 2 [sw1-Bridge-Aggregation2]intg1/0/3 [sw1-GigabitEthernet1/0/3]portlink-aggregation group 2 [sw1-Bridge-Aggregation2]intg1/0/4 [sw1-GigabitEthern...
[SwitchA-GigabitEthernet1/0/1]port link-aggregation group 1 6.端口G1/0/2与端口G1/0/1的配置一致 7. 建立汇聚组2 [SwitchA]interface bridge-aggregation 2 8.进入端口G1/0/3 [SwitchA]interface gigabitethernet1/0/3 9.参与端口汇聚的端口设置成全双工模式 [SwitchA-GigabitEthernet1/0/3]duplex ...
想把端口g1/0/49设置成port linkaggregation group1,但是输完命令后提示:can't assgin the port to the aggregation group because its attribute configurations are different than the aggregate interface 组网及组网描述: 设备是接入层交换机 型号 s5130 2022-12-24提问 举报 (0) 4 个回答 按时间 按赞数 ...
gathering,staticLACPaggregation,dynamicLACPaggregation. Experimentalenvironment:twoH3CE126A,ethernet1/0/24, ethernet1/0/23convergedintoalink. Handpooling: Configurationofthefirstswitch: [H3CA]link-aggregationgroup10modemanual [H3CA]interfaceEthernet1/0/24 ...
23 converged into a link. Hand pooling: Configuration of the first switch: [H3CA] link - aggregation group 10 mode manual [H3CA] interface Ethernet 1/0/24 H3CA - Ethernet1/0/24 port link aggregation group - 10 Can not specify a loopback - detection enable port as aggregation group ...
[S5820-if-range]port link-aggregation group 2 [S5820]int Bridge-Aggregation 2 [S5820-Bridge-Aggregation2]port link-type trunk [S5820-Bridge-Aggregation2]port trunk permit vlan all 4.2.配置svi地址 堆叠设备上配置SVI vlan 10 int vlan 10
port link-aggregation group 1 在Kubernetes中实现端口链路汇聚(port link-aggregation)组1(group 1)是一个常见的操作,特别是在需要提高网络带宽和可靠性的场景下。在本文中,我将向你介绍如何通过Kubernetes实现这一操作,以及详细的步骤和代码示例。 ### 步骤概述...
因为后边不用加“1”，一个端口只能属于一个聚合组，所以删除的时候，敲到group就可以了，不用跟后边...
怎么删除port link-aggregation group 1 步骤1 将原来已加入的聚合组的端口退出步骤2 删除聚合组命令参考如下,(具体的端口号,聚合组 请根据你的实际情况修改):interface GigabitEthernet 0/8 undo port link-aggregation group 1quitundo link-aggregation g