1.1.19 port link-aggregation group 1.1.20 reset lacp statistics1 以太网链路聚合 1.1 以太网链路聚合配置命令 1.1.1 display interface display interface命令用来显示聚合接口的相关信息。 【命令】 display interface [ route-aggregation [ interface-number ] ] [ brief [ description | down ] ] 【视图】 ...
[sw1-GigabitEthernet1/0/1]portlink-aggregation group 1 将该接口加入聚合组中 [sw1-Bridge-Aggregation1]int g1/0/2 进入到接口 [sw1-GigabitEthernet1/0/2]portlink-aggregation group 1 将该接口加入聚合组中 另外一台二层交换机配置方法一样。 看完配置但是要知道原理才是真正的懂,不然排错和稍微换...
想把端口g1/0/49设置成port linkaggregation group1,但是输完命令后提示:can't assgin the port to the aggregation group because its attribute configurations are different than the aggregate interface 组网及组网描述: 设备是接入层交换机 型号 s5130 2022-12-24提问 举报 (0) 4 个回答 按时间 按赞数 ...
port link-aggregation group 1 在Kubernetes中实现端口链路汇聚(port link-aggregation)组1(group 1)是一个常见的操作,特别是在需要提高网络带宽和可靠性的场景下。在本文中,我将向你介绍如何通过Kubernetes实现这一操作,以及详细的步骤和代码示例。 ### 步骤概述 要实现端口链路汇聚组1,我们需要按照以下步骤进行操作...
11.将端口加入汇聚组 [SwitchA-GigabitEthernet1/0/3]port link-aggregation group 2 12.负荷分担基于源MAC和目的MAC [SwitchA]link-aggregation load-sharing mode source-mac 13.端口G1/0/4与端口G1/0/3的配置一致 二、 SwitchB的配置顺序和配置内容同SwitchA的G1/0/1 ...
23 converged into a link. Hand pooling: Configuration of the first switch: [H3CA] link - aggregation group 10 mode manual [H3CA] interface Ethernet 1/0/24 H3CA - Ethernet1/0/24 port link aggregation group - 10 Can not specify a loopback - detection enable port as aggregation group ...
链路聚合(端口汇聚)配置(Linkaggregation(portaggregation)configuration)Linkaggregation(portaggregation)configurationPortwillconvergeismorethanoneEthernetportgrouptogethertoformalogicalgathering,usepoolingforupperentitytomorethanthephysicallinkwithinthesamegrouptogetherasalogicallink.Theportaggregationcanrealizethesharingofthetr...
因为后边不用加“1”,一个端口只能属于一个聚合组,所以删除的时候,敲到group就可以了,不用跟后边...
Enable link aggregation on the physical switch. Note: Link aggregation is also known as Ether-Channel, Ethernet trunk, port channel, LACP, vPC, and Multi-Link Trunking. Set up the ESXi Virtual Switch configuration to be compatible with these concepts. ...
例如:[Sysname]port-group manual group1 interface bridge-aggregationinterface-number 例如:[Sysname]interface bridge-aggregation1 3 port link-typetrunk 例如:[sysname-GigabitEthernet1/0/1]port link- type trunk 配置端口的链路类型为Trunk类型。交换机二层端口链路默认为Access类型,必须要使用本步命令进行转换,...