步骤三:将端口组的模式设置为active 最后,我们需要将端口组的模式设置为active。通过使用kubectl patch命令可以轻松地更新现有的端口组,将其模式设置为active。 ```bash kubectl patch portgroups my-port-group -p '{"spec":{"mode":"active"}}' ``` 通过以上步骤,你已经成功实现了“port-group 1 mode acti...
active(0) 启动端口的lacp协议,并设置为active模式; passive(1) 启动端口的lacp协议,并且设置为passive模式; on(2) 强制端口加入port channel,不启动lacp协议; 命令模式:接口配置模式 eg:在ethernet0/0/1端口模式下,将本端口以active模式加入port-group 1 switch(config-ethernet0/0/1)#port-group 1 mode acti...
Ruijie(config-if-range)#port-group 1 mode active Ruijie(config-if-range)#exit 三层静态聚合: Ruijie(config)#interface aggregatePort 1 Ruijie(config-if-AggregatePort 1)#no switchport Ruijie(config-if-AggregatePort 1)#ip address 1.1.1.1 24 Ruijie(config-if-AggregatePort 1)#exit Ruijie(config)#...
set lacp port [portlist] mode {active|passive} 端口参与聚合的模式是指在聚合组非静态模式下,聚合组内端口以主动或被动方式发送lacp 协议包来更新状态信息的方式。 当本端端口配置为主动协商模式时,对端端口可配置为主动或被动协商模式;当本端端口配置为被动协商模式时,对端端口只能配置为主动协商模式,否则不能...
channel-group 10 mode active NXOS2: interface port-channel10 interface Ethernet1/1 channel-group 10 mode active interface Ethernet1/2 channel-group 10 mode active Port-channel三层实验: NXOS1: interface port-channel20 no switchport ip address 20.20.20.1/24 interface Ethernet1/3 no switchport chan...
From Cisco MDS NX-OS Release 8.4(1), the CLI and the Device Manager create the port channel in Active mode on the NPIV core switches. The following table provides a comparison between On and Active modes. Table 1.Channel Group Configuration...
Get-NetTCPConnection|Group-Object-PropertyState, OwningProcess | Select-PropertyCount, Name, @{Name="ProcessName";Expression={(Get-Process-PID($_.Name.Split(',')[-1].Trim(' '))).Name}}, Group | Sort Count-Descending Most port leaks are caused by user-mode processes not correctly closin...
RowStatus { active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) } read-create 端口保护组行状态。 实现与MIB文件定义一致。 创建约束 创建该表的表项时必须指定索引hwPortProtectGroupId。 对表项使用set操作时,需完全符合SNMPv2创建标准。
switch-1(config)#interface eth1/1-2switch-1(config-if)#channel-group 1 mode activeswitch-1(config-if)#interface Po1switch-1(config-if)#switchport mode trunkswitch-1(config-if)#switchport trunk allowed vlan 1, 10-20switch-1(config-if)#vpc peer-linkswit...