step1:用qsys拉好niosii和板子上pl的連結 step2:在eclipse中將switch的address的值assgin給led的address的值 step3:燒上板子以後開關switch就會讓在其上的led也跟著開關 實驗二(使用niosII console輸入值來控制led的明暗) step1:sopcinfo同實驗一,只有.c檔的code要改 step2:燒上板子以後再在console中輸入...
Data[1] -> Use as regularr I/O DCLK -> Use as regular I/O FLASH_nCE/nCS0 -> Use as regular I/O You must check the device Pin-Out file for the Cyclone III device which you are using to make the following pins assignments: data0_to_the_epcs_controller -> DATA0 sdo_from the_...
4.直接在test1的project點選右鍵選擇build project,然後在rus an Nios II hardware即可以在console print出hello world 5.如果要讓led閃爍的話可以把led燈改成這以下的code就可以讓led累加了 https://ithelp.ithome.com.tw/upload/images/20220201/201451997eA0sNeD5v.png 參考資料:...
12. 左键选中app,点击Build Project编译led.c,编译完成可以看到生成app.elf文件。 五、下板测试 5.1 配置硬件 1. 将DE1-SOC开发板和电脑用板子自带的白色USB type B 线缆连接起来。给DE1-SOC插上电源并开机。 2. 打开Quartus的Programmer工具,点击Hardware Setup,选择DE-SOC[USB-1]端口。 2. 点击Auto Detec...
有網友問到如何在Nios II EDS的console輸入數字控制LED顯示,如輸入0則LEDG0亮,輸入1則LEDG1亮,以此類推。這是一個初學者熟悉Nios II與DE2很好的練習。 硬體部分的Nios II,這已經驅動了DE2上最常用的周邊,很適合初學者學習。 軟體部分 hello_world.c / C ...
async command result_t yellowOff(); async command result_t yellowToggle(); async command uint8_t get(); async command result_t set(uint8_t value); } 从该接口可以看出,该接口只有12个命令(command),没有事件(event)。LedsC组件就是实现该接口的命令。 因该接口大部分接口是类似的,故本文...
check OK -106 common/cmd_bootm.c Kernel subimage has wrong type 107 common/cmd_bootm.c Kernel subimage type OK -107 common/cmd_bootm.c Can't get kernel subimage data/size 108 common/cmd_bootm.c Got kernel subimage data/size -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)...
Hi, I load the DE2_NIOS_DEVICE_LED.sof programming file. Build and run the project; Plug in the USB cable on the USB device port on the DE2
but result was achieved, i.e. the "downloading issue" disappeared - in eclipse nios ii code is successfully downloaded and executed !!! So, probably for developing further the time violation issues should I start another topic ? Thanks. Translate led2_SDRAM_PLL_qsys_with_2nd_PLL...
Data[0] -> Use as regular I/O Data[1] -> Use as regularr I/O DCLK -> Use as regular I/O FLASH_nCE/nCS0 -> Use as regular I/O You must check the device Pin-Out file for the Cyclone III device which you are using to make the following pins assignments: ...