step1:用qsys拉好niosii和板子上pl的連結 step2:在eclipse中將switch的address的值assgin給led的address的值 step3:燒上板子以後開關switch就會讓在其上的led也跟著開關 實驗二(使用niosII console輸入值來控制led的明暗) step1:sopcinfo同實驗一,只有.c檔的code要改 step2:燒上板子以後再在console中輸入...
4.直接在test1的project點選右鍵選擇build project,然後在rus an Nios II hardware即可以在console print出hello world 5.如果要讓led閃爍的話可以把led燈改成這以下的code就可以讓led累加了 https://ithelp.ithome.com.tw/upload/images/20220201/201451997eA0sNeD5v.png 參考資料:...
In Cyclone® III devices, the EPCS controller does not automatically assign its output pins to the dedicated configuration pins on the FPGA. Instead, the output pins are exported to the top level design, giving users the flexibility to connect to any EPCS devices. Therefore, in order to use...
12. 左键选中app,点击Build Project编译led.c,编译完成可以看到生成app.elf文件。 五、下板测试 5.1 配置硬件 1. 将DE1-SOC开发板和电脑用板子自带的白色USB type B 线缆连接起来。给DE1-SOC插上电源并开机。 2. 打开Quartus的Programmer工具,点击Hardware Setup,选择DE-SOC[USB-1]端口。 2. 点击Auto Detec...
原廠Checksum Master範例的問題1.範例僅適用於Altera原廠的版子,並不適用於DE2。 2.範例中使用onchip memory,不過由於DE2上EP2C35F627C6 FPGA的logic element限制,onchip memory最多只能設定49K左右,但這樣的memory size仍無法執行此範例。 Solution本文並沒有打算重寫整個tutorial,所以建議先將Quartus II 7.2 Handb...
有網友問到如何在Nios II EDS的console輸入數字控制LED顯示,如輸入0則LEDG0亮,輸入1則LEDG1亮,以此類推。這是一個初學者熟悉Nios II與DE2很好的練習。 硬體部分的Nios II,這已經驅動了DE2上最常用的周邊,很適合初學者學習。 軟體部分 hello_world.c / C ...
- Timestamp Support: When CONFIG_TIMESTAMP is selected, the timestamp (date and time) of an image is printed by image commands like bootm or iminfo. This option is automatically enabled when you select CONFIG_CMD_DATE . - Partition Support: CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION...
本页面以流水灯为例 一,编写.v文件如下(代码贴下面):moduleflow_led(inputCLK_50M,inputRST_N, outputreg[3:0] ledA );reg[23:0] counter; always @(posedgeCLK_50Mor negedgeRST_N) begin if (!RST_N) counter < DE1-SOC开发板上搭建NIOS II处理器运行UCOS II ...
Hi, I load the DE2_NIOS_DEVICE_LED.sof programming file. Build and run the project; Plug in the USB cable on the USB device port on the DE2
Checksum Master為Quartus II 7.2 Handbook Vol:4中,示範使用Component Editor將user logic包成component後,並撰寫software driver的範例,但手冊中的程式和步驟都無法在DE2上順利執行,本文提出解決的方法。 使用環境 : Quartus II 7.2 SP1 + Nios II 7.2 SP1 + DE2 (Cyclone II EP2C35F627C6) ...