max_temp: 275 max_extrude_only_distance: 800.0 #control = pid #pid_kp = 16.644 #pid_ki = 1.099 #pid_kd = 63.038 [heater_bed] heater_pin: PG5 sensor_type: PT100 INA826 sensor_pin: PK2 min_temp: 0 max_temp: 100 #control = pid #pid_kp = 69.421 #pid_ki = 1.143 #pid_kd =...
#max_extrude_only_distance: 50.0 # 一次挤出或回抽的最大长度(以毫米耗材的长度为单位) # 如果一次挤出或回抽超过了这个值,这会导致返回一个错误 # 默认值是:50mm #max_extrude_only_velocity:6000 #max_extrude_only_accel:6000 # 最大的挤出和回抽速度(以毫米每秒为单位) # 和加速度(以毫米每二次方...
endstop_pin: ^PC4 position_endstop: 0.0 position_max: 205 [extruder] step_pin: PB1 dir_pin: !PB0 enable_pin: !PD6 microsteps: 16 rotation_distance: 34.410 nozzle_diameter: 0.400 filament_diameter: 1.750 max_extrude_only_distance: 500.0 max_extrude_only_velocity: 200.0 max_extrude_only_...
max_temp: 250 #pressure_advance = 0.010 #max_extrude_only_distance: 150.0 [tmc2660 extruder] cs_pin: PC17 spi_bus: usart1 interpolate: True run_current: 1.0 sense_resistor: 0.051 #[multi_pin hevacs] #pins: sx1509_duex:PIN_15, sx1509_duex:PIN_4 #Fan7&8 #[multi_pin my_fan] #p...
max_extrude_only_distance: 500 My full config is: https://www.dropbox.com/s/1tg9vleayfmfdne/printer.cfg?dl=0 File I'm trying to print (I did test other files): https://www.dropbox.com/s/nxp2uwrs9p5apvs/First_layer_test_box_25x25x1%2C5_0_PLA_0.2mm_94%25_0h_1m.gcode?dl...
max_extrude_only_distance: 700.0 step_pin: PA7 dir_pin: PA6 enable_pin: !PC4 microsteps: 16 rotation_distance: 7.1910 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PC9 sensor_type: EPCOS 100K B57560G104F sensor_pin: PC0 min_temp: 0 max_temp: 250 control: pid pid_Kp: ...
max_power: 1.0 min_extrude_temp: 170 control = pid pid_kp = 26.213 pid_ki = 1.304 pid_kd = 131.721 ## Try to keep pressure_advance below 1.0 pressure_advance: 0.05 ## Default is 0.040, leave stock pressure_advance_smooth_time: 0.040 ## In E0-MOT Position ## Make...
rotation_distance: 23.132 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PE4 sensor_type: PT100 INA826 sensor_pin: PK0 min_temp: 0 max_temp: 275 max_extrude_only_distance: 800.0 #control = pid #pid_kp = 16.644 #pid_ki = 1.099 ...
rotation_distance: 40 #主动轮周长mm full_steps_per_rotation:200 #单圈脉冲数量 endstop_pin:!PA15 position_min: 0 #限位最小行程 position_endstop: 0 #回零的位置 position_max: 210 #最大限位行程 homing_speed:50 #回零速度 second_homing_speed: 2 ...
max_extrude_only_distance: 100.0 step_pin: PB4 dir_pin: PB3 enable_pin: !PC3 microsteps: 16 # rotation_distance: 34.556 rotation_distance: 23.020 #rotation_distance: 22.855 #gear_ratio: 50:17 nozzle_diameter: 0.400 filament_diameter: 1.750 ...