#max_extrude_cross_section: # 挤出线条横截面的最大面积(以平方毫米为单位) # (例如:挤出线宽乘层高) # 这个设置能防止在相对较小的XY移动时产生过度的挤出 # 如果一个挤出速率请求超过了这个值,这会导致返回一个错误 # 默认值是:4.0 * 喷嘴直径 ^ 2 #instantaneous_corner_velocity: 1.000 # 两次挤出之...
max_extrude_cross_section:0.64#500挤出线条横截面的最大面积(以平方毫米为单位) (例如:挤出线宽乘层高)这个设置能防止在相对较小的XY移动时产生过度的挤出,默认值是:4.0 * 喷嘴直径 ^ 2 instantaneous_corner_velocity: 10.000 #两次挤出之间最大的速度变化(以毫米每秒为单位) max_extrude_only_distance: 100.0#...
Could not once print with Klipper as I always get "Move exceeds maximum extrusion (0.647mm^2 vs 0.640mm^2)" after the prime start code. Slicer is Cura 4.8. Printer is an Ender 3 with MicroSwiss and BMG. The example config for the SKR E3 board doesn't have _max_extrude_cross_sectio...
The maximum speed and acceleration of retraction moves are controlled in Klipper by the max_extrude_only_velocity and max_extrude_only_accel config settings. These settings have a default value that should work well on many printers. However, if one has configured a large retraction in the slice...
ar24 step_distance = 0.0106 nozzle_diameter = 0.4 filament_diameter = 1.75 max_extrude_cross_section = 1.5 max_extrude_only_distance = 200 heater_pin = ar10 sensor_type = EPCOS 100K B57560G104F sensor_pin = analog13 control = pid pid_kp = 29.865 pid_ki = 1.933 pid_kd = 115.353 ...
{% set max_extrude_cross_section = printer.configfile.settings.extruder.max_extrude_cross_section | float %} @@ -205,28 +207,28 @@ gcode: {% set z_offset = printer.configfile.config.cartographer.z_offset %} {% endif %} # Prime Line Volumetric Calculations # Calculos volumetricos para...
mesh_min应该大于y_offset值 no trigger on probe after full movement完全移动后未触发探针 mesh_min值的问题,该值未设置好导致探针没在热床范围内,该值为正值应该大于y_offset 目前就更新这么多,大家碰到啥解决不了的问题也可以发在评论区,解决后我会整合进该专栏 ...
In general, that's bad because it actually needs to be noticeable. Are you sure you have increased the homing speed (and the max speed for z axis)? Edit: or did you mean just the regular axes move? If the latter, it's fine. You just need to look at the homing graph. ...
#max_extrude_cross_section: # 挤出线条横截面的最大面积(以平方毫米为单位) # (例如:挤出线宽乘层高) # 这个设置能防止在相对较小的XY移动时产生过度的挤出 # 如果一个挤出速率请求超过了这个值,这会导致返回一个错误 # 默认值是:4.0 * 喷嘴直径 ^ 2 ...
max_extrude_cross_section:0.64#500挤出线条横截面的最大面积(以平方毫米为单位) (例如:挤出线宽乘层高)这个设置能防止在相对较小的XY移动时产生过度的挤出,默认值是:4.0 * 喷嘴直径 ^ 2 instantaneous_corner_velocity: 10.000 #两次挤出之间最大的速度变化(以毫米每秒为单位) ...