rotation_distance: 8 endstop_pin: ^!PA7 #position_endstop: 304 position_max: 302 homing_speed: 10.0 position_min: -1.0 [extruder] step_pin: PL7 dir_pin: PL6 enable_pin: !PC0 microsteps: 16 # 382.165 full_steps_per_rotation: 200 gear_ratio: 50:17 rotation_distance: 23.132 nozzle_...
# See docs/Config_Reference.md for a description of parameters. # The primary extruder [extruder] step_pin: ar26 dir_pin: ar28 enable_pin: !ar24 microsteps: 16 rotation_distance: 33.500 nozzle_diameter: 0.500 filament_diameter: 3.500 heater_pin: ar10 sensor_type: EPCOS 100K B57560G104F ...
#主动带轮周长mm(2GT-20T带轮40,2GT-16T带轮32) rotation_distance: 40 #电机单圈脉冲数(1.8度电机:200,0.9度电机:400) full_steps_per_rotation: 200 #减速比(Z轴大小带轮比为80:16,输出轴在前,输入轴在后) gear_ratio: 80:16 # z轴最小行程--软件限位position_max: 300 position_min: -1 #...
[extruder] step_pin:PA4 dir_pin:PA6 enable_pin:!PA2 microsteps:16 rotation_distance:25.12 gear_ratio:50:17 full_steps_per_rotation:200 max_power:1.0 pressure_advance:0.089 #gear_ratio: # 以上参数详见“stepper”配置分段。 # 如果未指定任意上述参数,则没有步进电机与热端相关联 # (尽管使用SYN...
PD15#---Klipper0.9以上版本设置---#电机细分microsteps:16#主动带轮周长mm(2GT-20T带轮40,2GT-16T带轮32)rotation_distance:40#电机单圈脉冲数(1.8度电机:200,0.9度电机:400)full_steps_per_rotation:200#减速比(Z轴带轮比为80:16,输出轴在前,输入轴在后)gear_ratio:80:16...
If the rotation distance is a negative number then the stepper motion will be inverted (relative to the stepper direction specified in the config file). Changed settings are not retained on Klipper reset. Use with caution as small changes can result in excessive pressure between extruder and ...
Sensorless homing with autotuning enabled is known to work on TMC2209, TMC2240 and TMC5160, provided you home fast enough (homing_speed should be numerically greater than rotation_distance for those axes using sensorless homing). As always, be very careful when trying sensorless homing for the ...
[extruder] step_pin: PD5 dir_pin: PA1 enable_pin: !PC6 microsteps: 16 full_steps_per_rotation: 400 rotation_distance: 7.97 nozzle_diameter: 0.600 filament_diameter: 1.750 #___ HEATER NOZZLE ___ heater_pin: !PA20 #___NOZZLE TEMP ___ sensor_type: EPCOS 100K...
[extruder] step_pin: PD5 dir_pin: !PD6 enable_pin: !PD4 ## Update value below when you perform extruder calibration ## If you ask for 100mm of filament, but in reality it is 98mm: ## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100 #...
[extruder] step_pin: PD5 dir_pin: !PD6 enable_pin: !PD4 ## Update value below when you perform extruder calibration ## If you ask for 100mm of filament, but in reality it is 98mm: ## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100 #...