首先需要对 z 距离有一个概念,一般 0.4mm 喷嘴,调平时肉眼可见的线条变化为 0.05mm。 这个值是经验归纳的,在边打首层边调整 z offset 时很喜欢用这个变化值来调整。 命令测试 通过klipper 自带的命令可以测试接近开关触发时的 z 值,使用这个值判断各因素的影响大小:https://www.klipper3d.org/zh/Probe_Cali...
我们移动xy轴,把bltouch的探针移动到热床中间位置,输入PROBE_CALIBRATE,探针弹出,打印头下移,当探针碰到热床会自动弹起,并移动挤出头到中间位置 我们在挤出头和热床之间放一张纸,输入TESTZ Z=-0.1为向下移动0.1mm,输入TESTZ Z=+0.1为向上移动0.1mm。输入TESTZ Z=-或者Z=+则移动到前两个值的中值位置从而缩...
# 进入配置文件所在目录cd~/printer_data/config# 下载klicky-probe.cfg需要的宏命令wget https://raw.githubusercontent.com/jlas1/Klicky-Probe/main/Klipper_macros/Klipper_macros.zip# 解压unzip Klipper_macros.zip# 解压以后新增的文件klicky-probe.cfg#选择要开启功能的配置文件klicky-variables.cfg#存储Klicky...
offsets. The default is the relative_reference_index # of the configured bed_mesh, if configured. It's possible to change the relative # reference index at runtime or use the GCode argument BED_POSITION of CALIBRATE_Z. switch_offset: # The trigger point offset of the used mag-probe ...
Klipper is a 3d-printer firmware. Contribute to Klipper3d/klipper development by creating an account on GitHub.
[tmc2208 stepper_z3] uart_pin: PD10#microsteps: 16interpolate: True run_current:0.9hold_current:0.7sense_resistor:0.110stealthchop_threshold:200### # Heater Bed 热床设置 ###[heater_bed]#热床加热器控制Pin脚 (BED OUT)heater_pin: PB4#热床温度...
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) ## (+) value = endstop above Z0, (-) value = endstop below ## Increasing position_endstop brings nozzle closer to the bed ## After you run Z_ENDSTOP_CALIBRATE, position_endstop will...
Calibrate Z Offset, Avoid Z Upset! Klipper: Z Offset Calibration – Simply Explained byAndreas Giencke Published Apr 5, 2023 In Klipper, Z offset calibration is a basic but important procedure. Read on to learn all about how it's done!
[tmc2208 stepper_z3] uart_pin: PD10#microsteps: 16interpolate: True run_current:0.9hold_current:0.7sense_resistor:0.110stealthchop_threshold:200### # Heater Bed 热床设置 ###[heater_bed]#热床加热器控制Pin脚 (BED OUT)heater_pin: PB4#热床温度...
mesh_min应该大于y_offset值 no trigger on probe after full movement完全移动后未触发探针 mesh_min值的问题,该值未设置好导致探针没在热床范围内,该值为正值应该大于y_offset 目前就更新这么多,大家碰到啥解决不了的问题也可以发在评论区,解决后我会整合进该专栏 ...