完成测试后,在配置中的[extruder]节中加入pressure_advance = <calculated_value>(其中calculated_value为前述测试计算出的数值),保存并使用 RESTART 命令重启Klipper以应用配置。同时RESTART会重置转角速度设置并取消压力提前值的逐层变化的设置。 6、热床PID校准 PID_CALIBRATE HEATER=heater_bed TARGET=100 7、热端...
通过ssh连接鲁班猫,执行以下命令。 # 进入配置文件所在目录cd~/printer_data/config# 下载klicky-probe.cfg需要的宏命令wget https://raw.githubusercontent.com/jlas1/Klicky-Probe/main/Klipper_macros/Klipper_macros.zip# 解压unzip Klipper_macros.zip# 解压以后新增的文件klicky-probe.cfg#选择要开启功能的配置...
#pressure_advance_smooth_time: 0.040 # A time range (in seconds) to use when calculating the average # extruder velocity for pressure advance. A larger value results in # smoother extruder movements. This parameter may not exceed 200ms. # This setting only applies if pressure_advance is non-...
sensor_pin: PC0# 喷嘴直径nozzle_diameter:0.400# 加热棒PWM最大输出功率max_power:1.0# 加热棒最低挤出温度(达到此温度挤出机才能有挤出动作)min_extrude_temp:170# pid控制参数control = pid pid_kp =26.213pid_ki =1.304pid_kd =131.721pressure_advance:0.05pressure_advance_smooth_time:0.040 [tmc220...
Pressure_Advance.md Probe_Calibrate.md Protocol.md README.md RPi_microcontroller.md Releases.md Resonance_Compensation.md Rotation_Distance.md SDCard_Updates.md Skew_Correction.md Slicers.md Sponsors.md Status_Reference.md TMC_Drivers.md TSL1401CL_Filament_Width_Sensor.md Using_PWM_Tools.m...
pressure_advance.test printers.test pwm.cfg pwm.test quad_gantry_level.test rotary_delta_calibrate.cfg rotary_delta_calibrate.test screws_tilt_adjust.cfg screws_tilt_adjust.test sdcard_loop.cfg sdcard_loop.test temperature.cfg temperature.test tmc.cfg tmc.test z_tilt.cfg z_tilt.te...
"target", "temperature", "pressure_advance", "smooth_time", "power"] for h in self.printer.get_heaters(): requested_updates['objects'][h] = ["target", "temperature", "power"] for f in self.printer.get_fans(): requested_updates['objects'][f] = ["speed"] ...
pressure_advance_smooth_time: 0.040 ## In E0-MOT Position ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 extruder] uart_pin: PD7 interpolate: false run_current: 0.5 hold_current: 0.2 sense_resistor: 0.110 stealthchop_threshold: 0 ### # Be...
pid_kp =26.213pid_ki =1.304pid_kd =131.721pressure_advance:0.05pressure_advance_smooth_time:0.040 [tmc2208 extruder] uart_pin: PA15#microsteps: 16interpolate: True run_current:0.6hold_current:0.4sense_resistor:0.110stealthchop_threshold:200###Z0轴设置###[stepper_z]#Z0电机脉冲引脚设置s...
pressure_advance_smooth_time: 0.09 max_extrude_cross_section:0.64#500挤出线条横截面的最大面积(以平方毫米为单位) (例如:挤出线宽乘层高)这个设置能防止在相对较小的XY移动时产生过度的挤出,默认值是:4.0 * 喷嘴直径 ^ 2 instantaneous_corner_velocity: 10.000 #两次挤出之间最大的速度变化(以毫米每秒为单位...