在打印之前还要在console中输入:SET_PRESSURE_ADVANCE ADVANCE=0 把pressure_advance设置为0 另外如果你之前在配置中加入过input_shaper 那么我们要SET_INPUT_SHAPER SHAPER_FREQ_X=0 SHAPER_FREQ_Y=0 确保基础值是0 。 再输入TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=1250 FACTOR=100 BAND=5...
记录一下我的压力提前调试 一、到模型文件地址 生成模型文件https://realdeuce.github.io/Voron/PA/pressure_advance.html看不懂就用浏览器翻译一下。修改了挤出乘数为1.0,高度0.15mm,开始结束G代码与打印面积,其他的不动。 打开下载的G文件,修改温度参数M104S200; set extruder tempM140S60; set bed tempM180S60...
pressure_advance_smooth_time: 0.040 [tmc2208 extruder] uart_pin: PA15 #microsteps: 16 interpolate: True run_current: 0.6 hold_current: 0.4 sense_resistor: 0.110 stealthchop_threshold: 200 ### Z0轴设置 ### [stepper_z] #Z0电机脉冲引脚设置 step_pin: PE2 #Z0电机方向引脚设置,可以通过添或删...
TheM900command is implemented by calling Klipper'sSET_PRESSURE_ADVANCEcommand. TheKfactor is scaled byvariable_pressure_advance_scale(default:-1.0). If the scaling value is negative theM900command has no effect. Optional Configs Bed Mesh
pid_kp =26.213pid_ki =1.304pid_kd =131.721pressure_advance:0.05pressure_advance_smooth_time:0.040 [tmc2208 extruder] uart_pin: PA15#microsteps: 16interpolate: True run_current:0.6hold_current:0.4sense_resistor:0.110stealthchop_threshold:200###Z0轴设置###[stepper_z]#Z0电机脉冲引脚设置s...
TheM900command is implemented by calling Klipper'sSET_PRESSURE_ADVANCEcommand. TheKfactor is scaled byvariable_pressure_advance_scale(default:-1.0). If the scaling value is negative theM900command has no effect.
pressure_advance_smooth_time: 0.040 ## In E0-MOT Position ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 extruder] uart_pin: PD7 interpolate: false run_current: 0.5 hold_current: 0.2 sense_resistor: 0.110 ...
pressure_advance_smooth_time: 0.040 ## In E0-MOT Position ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 extruder] uart_pin: PD7 interpolate: false run_current: 0.5 hold_current: 0.2 sense_resistor: 0.110 stealthchop_threshold: 0 ### # Be...
pid_kp =26.213pid_ki =1.304pid_kd =131.721pressure_advance:0.05pressure_advance_smooth_time:0.040 [tmc2208 extruder] uart_pin: PA15#microsteps: 16interpolate: True run_current:0.6hold_current:0.4sense_resistor:0.110stealthchop_threshold:200###Z0轴设置###[stepper_z]#Z0电机脉冲引脚设置s...
TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=.020 压力提前的设定值可以通过pressure_advance = <start> + <measured_height> * <factor>进行计算,如测出的最优层高(measured_height)为12.9 mm,测试起始点(start)为0 mm,增量(factor)为0.02,则计算结果为 0 + 12.90 *.020=0.2...