pressure_advance_smooth_time: 0.040 [tmc2208 extruder] uart_pin: PA15 #microsteps: 16 interpolate: True run_current: 0.6 hold_current: 0.4 sense_resistor: 0.110 stealthchop_threshold: 200 ### Z0轴设置 ### [stepper_z] #Z0电机脉冲引脚设置 step_pin: PE2 #Z0电机方向引脚设置,可以通过添或删...
dir_pin:PA6 enable_pin:!PA2 microsteps:16 rotation_distance:25.12 gear_ratio:50:17 full_steps_per_rotation:200 max_power:1.0 pressure_advance:0.089 #gear_ratio: # 以上参数详见“stepper”配置分段。 # 如果未指定任意上述参数,则没有步进电机与热端相关联 # (尽管使用SYNC_EXTRUDER_MOTION命令可能可...
pressure_advance: 0.02 #压力提前数据 pressure_advance_smooth_time: 0.09 max_extrude_cross_section:0.64#500挤出线条横截面的最大面积(以平方毫米为单位) (例如:挤出线宽乘层高)这个设置能防止在相对较小的XY移动时产生过度的挤出,默认值是:4.0 * 喷嘴直径 ^ 2 instantaneous_corner_velocity: 10.000 #两次挤出...
来改变电机的运转方向dir_pin: PD13#Z3电机使能引脚设置enable_pin: !PD15#---Klipper0.9以上版本设置---#电机细分microsteps:16#主动带轮周长mm(2GT-20T带轮40,2GT-16T带轮32)rotation_distance:40#电机单圈脉冲数(1.8度电机:200,0.9度电机:400)full_steps_per_rotation:200#减速比(Z轴带轮比为80:16...
#pressure_advance = 0.010 #max_extrude_only_distance: 150.0 [tmc2660 extruder] cs_pin: PC17 spi_bus: usart1 interpolate: True run_current: 1.0 sense_resistor: 0.051 #[multi_pin hevacs] #pins: sx1509_duex:PIN_15, sx1509_duex:PIN_4 #Fan7&8 ...
pressure_advance: The current pressure advance value. smooth_time: The current pressure advance smooth time. motion_queue: The name of the extruder that this extruder stepper is currently synchronized to. This is reported as None if the extruder stepper is not currently associated with an ...
I installed TMC2208 drivers and configured pressure advance (pressure_advance = 0.5). Sometimes during a print the extruder stepper disables itself and stops extruding. When trying again without any changes to the settings, the same print would then succeed. My retraction speed is set to 40mm/s...
pressure_advance_smooth_time: 0.040 ## In E0-MOT Position ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 extruder] uart_pin: PD7 interpolate: false run_current: 0.5 hold_current: 0.2 sense_resistor: 0.110 ...
pressure_advance_smooth_time: 0.040 ## In E0-MOT Position ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 extruder] uart_pin: PD7 interpolate: false run_current: 0.5 hold_current: 0.2 sense_resistor: 0.110 stealthchop_threshold: 0 ### # Be...
pid_kp =26.213pid_ki =1.304pid_kd =131.721pressure_advance:0.05pressure_advance_smooth_time:0.040 [tmc2208 extruder] uart_pin: PA15#microsteps: 16interpolate: True run_current:0.6hold_current:0.4sense_resistor:0.110stealthchop_threshold:200###Z0轴设置###[stepper_z]#Z0电机脉冲引脚设置s...