1 前言: 链路聚合可以增加带宽，加上单链路故障，好处不多说，直接看实验.实验拓扑如下：创建聚合口，直接在配置模式下输入：interface Bridge-Aggregation 1然后分布把图上的口加入到这个聚合口中来，在接口视图下输入：port link-aggregation group 1都添加好之后，查看配置聚合口状态，输入“display link-aggregation ...
ip address 192.168.1.1 255.255.255.0 link-aggregation global load-sharing mode destination-ip #ip地址进行负载分担 link-aggregation mode dynamic #动态聚合模式 interface range g0/0/0 to g0/0/1 lacp mode passive port link-aggregatio group 2
18、1/0/2SWA-Ethernet1/0/2port link-aggregation group 1链路聚合交换机SWB的配置与交换机 SWA类似,在此不再赘述。配置完成后,在交换机SWA上执行display link-aggregation summary命令显示结果如下: SWAdisplay link-aggregation summaryAggregati on In terface Type:BAGG - Bridge-Aggregation, RAGG - Route-Ag...
interface GigabitEthernet2/0/2 port link-type trunk port trunk permit vlan all port link-aggregation group 1
H3C Ethernet Link Aggregation 1. 以太网链路聚合简介 以太网链路聚合通过将多条以太网物理链路捆绑在一起形成一条以太网逻辑链路,实现增加链路带宽的目的,同时这些捆绑在一起的链路通过相互动态备份,可以有效地提高链路的可靠性。 如图所示,Device A与Device B之间通过三条以太网物理链路相连,将这三条链路捆绑在一...
[H3C-Ethernet1/0/1]port link-aggregation group agg-id 首先，创建一个链路汇聚组并指定其类型为手工汇聚还是静态LACP汇聚，然后将相应的端口加入到汇聚组中。需要注意的是，如果要在两台交换机之间配置链路聚合，应尽量保持两台交换机之间相连端口的一致性（即端口Ethernet1/0/1与对端的Ethernet1/0/1相连，...
[EZ-4-I-2switch]interface Bridge-Aggregation 1 3.然后需要的口加入到这个聚合口中来,在接口视图下输入: interface GigabitEthernet1/0/40 description pppoe3-a speed 100 undo ndp enable undo ntdp enable 4.都添加好之后,查看配置聚合口状态,输入“display link-aggregation verbose”,如下图:...
1.1.1 Introduction to Link Aggregation 1.1.2 Introduction to LACP 1.1.3 Operation Key 1.1.4 Manual Aggregation Group 1.1.5 Static LACP Aggregation Group 1.1.6 Dynamic LACP Aggregation Group 1.1.7 Restriction of LPU types on Link Aggregation ...
查看链路聚合 dis link-aggregation verbose 配置SwitchA 1. 建立汇聚组1 [SwitchA]interface bridge-aggregation 1 2.进入端口G1/0/1 [SwitchA]interface gigabitethernet1/0/1 3.参与端口汇聚的端口设置成全双工模式 [SwitchA-GigabitEthernet1/0/1]duplex full ...
Chapter 1 Link Aggregation Overview 1.1 Link Aggregation 1.1.1 LACP 1.1.2 Consistency Considerations for Ports in an Aggregation 1.2 Approaches to Link Aggregation 1.2.1 Manual Link Aggregation 1.2.2 Static LACP link aggregation 1.3 Load Sharing in a Link Aggregation Group ...