interface route-aggregation 2 ip address 192.168.1.1 255.255.255.0 link-aggregation global load-sharing mode destination-ip #ip地址进行负载分担 link-aggregation mode dynamic #动态聚合模式 interface range g0/0/0 to g0/0/1 lacp mode passive port link-aggregatio group 2...
1 前言: 链路聚合可以增加带宽，加上单链路故障，好处不多说，直接看实验.实验拓扑如下：创建聚合口，直接在配置模式下输入：interface Bridge-Aggregation 1然后分布把图上的口加入到这个聚合口中来，在接口视图下输入：port link-aggregation group 1都添加好之后，查看配置聚合口状态，输入“display link-aggregation ...
link-aggregation selected-port minimum min-number// 以数值方式配置聚合组中的最小选中端口数 link-aggregation selected-port minimum percentage number// 以百分比方式配置聚合组中的最小选中端口数 缺省情况下,聚合组中的最小选中端口数不受限制 link-aggregation selected-port maximum max-number [ lacp-sync ]...
port link-aggregation group 1 quit interface Ten-GigabitEthernet1/0/26 port link-aggregation group 1 quit interface Bridge-Aggregation 1 port link-type trunk port trunk permit vlan 20 to 30 undo port trunk permit vlan 1 检查验证: display interface brief 查看Bridge-Aggregation 1 接口是否UP displa...
7、Ethernet1/0/1quitSWAinteface Ethernet 1/0/2SWA-Ethernet1/0/2undo loopback-detection enableSWA-Ethernet1/0/2port link-aggregation group 1交换机SWB的配置与交换机 SWA类似,在此不再赘述。配置完成后,在交换机SWA上执行display link-aggregation summary命令显示结果如下SWAdisplay link-aggregation summar...
[SwitchA-GigabitEthernet1/0/1]port link-aggregation group 1 6.端口G1/0/2与端口G1/0/1的配置一致 7. 建立汇聚组2 [SwitchA]interface bridge-aggregation 2 8.进入端口G1/0/3 [SwitchA]interface gigabitethernet1/0/3 9.参与端口汇聚的端口设置成全双工模式 ...
port access vlan 10 配置聚合接口: interface Bridge-Aggregation1 interface GigabitEthernet1/0/3 port link-aggregation group 1 interface GigabitEthernet1/0/4 port link-aggregation group 1 设置聚合端口为干路,允许VLAN 10和20: interface Bridge-Aggregation1 ...
[DeviceA-Bridge-Aggregation1] port link-type trunk #配置聚合组端口类型为trunk [DeviceA-Bridge-Aggregation1] port trunk permit vlan 10 20 #允许vlan 10 20通过 [DeviceA-Bridge-Aggregation1] link-aggregation mode dynamic #配置链路聚合模式为动态LACP模式 ...
port link-aggregation group group-id 多次执行此步骤可将多个三层以太网接口加入聚合组。 (6) (可选)配置端口优先级。 link-aggregation port-priority priority 缺省情况下,端口优先级为32768。 2. 配置三层动态聚合组 (1) 进入系统视图。 system-view (2) 配置系统的LACP优先级。 lacp system-priority priorit...
port link-aggregation group99#加入链路聚合组 注意:如果链路聚合组不成功时,尝试进入聚合组,shutdown,然后再undo shutdown。再观察链路聚合状态。 删除链路聚合: interfaceGigabitEthernet1/0/1undo port link-aggregation group99quit undo link-aggregation group99 ...