port link-aggregation group 1 # [S1]dis link-aggregation verbose Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing Port: A -- Auto Port Status: S -- Selected, U -- Unselected, I -- Individual Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation, D --...
port link-aggregation group group-id// 将三层以太网接口加入聚合组 link-aggregation port-priority priority// (可选)配置端口优先级 5.3.2 配置三层动态聚合组 interface route-aggregation interface-number 创建三层聚合接口后,系统将自动生成同编号的三层聚合组,且该聚合组缺省工作在静态聚合模式下 link-aggregati...
1.1.37 link-aggregation load-sharing mode 1.1.38 link-aggregation load-sharing mode local-first 1.1.39 link-aggregation management-port 1.1.40 link-aggregation management-subnet 1.1.41 link-aggregation management-vlan 1.1.42 link-aggregation mode 1.1.43 link-aggregation port-priority 1.1.44 link-...
· lacp system-priority 1.1.3 display link-aggregation load-sharing mode display link-aggregation load-sharing mode命令用来显示全局或聚合组内采用的聚合负载分担类型。 【命令】 display link-aggregation load-sharing mode [ interface [ bridge-aggregation interface-number ] ] 【视图】 任意视图 【缺省用户...
ip address 192.168.1.1 255.255.255.0 link-aggregation global load-sharing mode destination-ip #ip地址进行负载分担 link-aggregation mode dynamic #动态聚合模式 interface range g0/0/0 to g0/0/1 lacp mode passive port link-aggregatio group 2
link-aggregation port-priorityH3C交换机端口链路聚合 交换机配置: 交换机4个光口中,交换机18和20号端口连接测试仪10/1和10/2端口,交换机此两个端口进行绑定端口聚合,交换机22和24号端口连接被测试设备10/1和10/2端口,交换机此两个端口绑定端口聚合。
port link-aggregation group group-id [ force ] (可选)配置端口优先级 link-aggregation port-priority priority 缺省情况下,端口优先级为32768 2. 配置二层动态聚合组表1-7 配置二层动态聚合组操作 命令 说明 进入系统视图 system-view - 创建二层聚合接口,并进入二层聚合接口视图 interface bridge-agg...
[SWA]lacp system-priority[number] 配置端口的优先级 代码语言:javascript 复制 [SWA-GigabitEthernet1/0/1]link-aggregation port-priority[number] 系统的LACP协议优先级和端口的LACP协议优先级均为32768,改变系统的LACP协议优先级会影响到动态聚合组成员的Selected和Unselected状态。
port link-aggregation group 3#interface GigabitEthernet1/0/4 port link-type trunk port trunk permit vlan all port link-aggregation group 3#m-lag mad exclude interface GigabitEthernet1/0/5m-lag system-mac 0001-0001-0001m-lag system-number 1m-lag system-priority 666m-lag consistency-check ...
【缺省用户角色】network-admin mdc-admin 【参数】system-priority：系统的LACP优先级，取值范围为0～65535。该数值越小，优先级越高。【举例】配置系统的LACP优先级为64。<Sysname> system-view [Sysname] lacp system-priority 64 【相关命令】· link-aggregation port-priority ...