void setup() { timer1_isr_init(); timer1_enable(TIM_DIV1, TIM_EDGE, TIM_LOOP); //此处选择div模式,timer触发方式(不要改),timer_loop循环,SINGLE单次 timer1_write(25000); //修改计数比较器,这里为25000个间隔触发中断,变量用uint32_t timer1_attachInterrupt(userFunc); } ICACHE_RAM_ATTR void...
There are two timers in ESP8266 Timer0 and Timer1, one timer is used by its WiFi functions. We get only one timer to work. To avoid crash issues I recommend use of Ticker instead of Timer. Ticker performs same function as timer. In this tutorial we will see both Timer and Ticker exa...
NULL); // 然后使能定时器 os_timer_arm(&OS_Timer_1, time_ms, time_repetitive); } 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 这里也要定义一个全局变量软件定时类型变量 代码: AI检测代码解析 os_timer_t OS_Timer_1; // 定义定时器全局变量 1. 接下来我们继续...
因为任务可能被中断,或者被其他高优先级的任务延迟,因此以下os_timer系列的接口并不能保证定时器精确执行。如果需要精确的定时,例如,周期性操作某GPIO,请使用硬件中断定时器,具体可参考hw_timer.c,硬件定时器的执行函数在中断里被执行。 注意: 对于同一个timer, os_timer_arm或os_timer_arm_us不能重复调用,必须...
ETS_GPIO_INTR_ENABLE(); 注:参考手册esp8266-technical_reference_cn的20页。 然后是硬件定时器的使用,使用方法也很简单,共分3步: 1、选择中断源,选择定时器是否自动填充 hw_timer_init(0,1); 该函数共有两个参数: 参数1:选择中断源。0,使用 FRC1 中断源,1,使用 NMI 中断源 ...
1. 修改用户工程目录的 MakeFile,在 CONFIGURATION_DEFINES 后加宏定义:-DMEMLEAK_DEBUG 如:CONFIGURATION_DEFINES = -DMEMLEAK_DEBUG 2. 在用户代码,如 user_main.c 中,增加如下代码: #include "mem.h" bool ICACHE_FLASH_ATTR check_memleak_debug_enable (void) ...
os_install_putc1((void *)uart0_write_char_no_wait); //use thistoprint via uart0#if UART_SELFTEST&UART_BUFF_ENos_timer_disarm(&buff_timer_t);os_timer_setfn(&buff_timer_t, uart_test_rx ,NULL); //a demotoprocess the datainuart rx bufferos_timer_arm(&buff_timer_t,10,1);#...
1);//高电平点亮,常亮 PIN_FUNC_SELECT(PERIPHS_IO_MUX_MTDI_U,FUNC_GPIO12);//黄灯 GPIO_OUTPUT_SET(GPIO_ID_PIN(12),0);//低电平点亮,常亮 PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO2_U,FUNC_GPIO2);//蓝灯 os_timer_disarm(&blue_led_timer); os_timer_setfn(&blue_led_timer, (os_timer_...
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2,ENABLE); //串口2时钟使能USART_DeInit(USART2); /...
GPIO,5,1 if %eventvalue%=8 and [int#1]<>1 //快速煮饭 let,1,1 //临时变量1=1 let,2,1 //临时变量2=1 timerSet_ms,2,200 //激活Rules#Timer=2 程序 endif if %eventvalue%=1 GPIO,4,1 timerSet_ms,1,200 endif if %eventvalue%=2 ...