Hello, I have a problem concerning the writing of the pins. I want to put them to 1 to drive a Multiplexers (MUXO & MUXI in the code below) but when i try to control MUXI, i have the error code in the Serial terminal "E (X) gpio: gpio_set_level(226): GPIO output gpio_num...
函数名:HAL_GPIO_ReadPin(参数1,参数2) 函数作用:读取对应的引脚电平 返回值:若读取到高电平,则返回GPIO_PIN_SET;反之,读取到低电平,则返回GPIO_PIN_RESET 参数1:GPIOx 对应GPIO总线,其中x可以是A...I,例如PH10,则输入GPIOH 参数2:GPIO_Pin 对应引脚数,可以是1...15,例如PH10,则输入GPIO_PIN_10 五...
#define PA_ENABLE_GPIO GPIO_NUM_48 int8_t get_pa_enable_gpio(void) { return PA_ENABLE_GPIO; } void es8311_pa_power(bool enable) { if (enable) { gpio_set_level(get_pa_enable_gpio(), 1); } else { gpio_set_level(get_pa_enable_gpio(), 0); } } 1. 2. 3. 4. 5. 6. ...
boolLED=(bool)gpio_get_level(LED_GPIO);gpio_set_level(LED_GPIO,!LED);//gpio_set_level(LED_...
// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex) // so changing it here has no effect // #define SUPPORT_TRANSACTIONS 三、运行与测试 1.首先打开如下路径的示例程序 示例程序路径 .pio\libdeps\esp32dev\lv_arduino\examples\ESP32_TFT_eSPI\ESP32_TFT_eS...
//! GPIO interrupt//!//! This prints "Interrupt" when the boot button is pressed.//! It also blinks an LED like the blinky example.#![no_std]#![no_main]usecore::cell::RefCell;usecritical_section::Mutex;useesp32c3_hal::{
// USER DEFINED SETTINGS// Set driver type, fonts to be loaded, pins used and SPI control method etc./// See the User_Setup_Select.h file if you wish to be able to define multiple// setups and then easily select which setup file is used by the compiler./// If this file is edi...
intr_type = GPIO_PIN_INTR_DISABLE; /* 禁止中断 */ /* 根据设定参数初始化并使能 */ gpio_config(&gpio_config_structure); while (1) { gpio_set_level(GPIO_LED_NUM, 0); /* 熄灭 */ vTaskDelay(500 / portTICK_PERIOD_MS); /* 延时500ms*/ gpio_set_level(GPIO_LED_NUM, 1); /...
static void ADC_SetCS(void) { gpio_set_level(14, 1); } static void ADC_ClrCS(void) { gpio_set_level(14, 1); } void app_main(void) { //=== I2C init === i2c_config_t conf; conf.mode = I2C_MODE_MASTER; conf.sda_io_num = I2C_LCD_EXPANDER_MASTER_SDA_IO; conf.scl_io_...
Decoding stack results 0x400e93b0: gpio_set_level at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/hal/esp32/include/hal/gpio_ll.h line 427 0x400e5ad9: __digitalWrite at C:\Users\ACER\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0....