W (332) main: Force reset 4g board I (336) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 I (3851) main: === I (3851) main: ESP 4G Cat.1 Wi-Fi Router I (3851) main: === I (3856) gpio: GPIO[15...
We have also tried to "force" the continuous reset situation to debug by setting cmd to 1 in between the two lines below. When we do that, the device does indeed reset (panic) as expected - but boots normally in that case. The I2C fault that causes the crash in the first place is:...
XPD_SDIO_TIEH (BLOCK0) If XPD_SDIO_FORCE & XPD_SDIO_REG = 1.8V R/- (0b0) XPD_SDIO_FORCE (BLOCK0) Ignore MTDI pin (GPIO12) for VDD_SDIO on reset = False R/- (0b0) Flash voltage (VDD_SDIO) determined by GPIO12 on reset (High for 1.8V, Low/NC for 3.3V)Attachments...
secure_boot_rw_protect = True #开启secure boot key区域的读写保护 [FLASH ENCRYPTION] flash_encryption_en = True #开启flash加密功能 burn_flash_encryption_key = True #使能flash encrypt key烧写 flash_encrypt_force_write = False #是否不检查flash encrypt key block,强制烧写key flash_encrypt_rw_prote...
EFUSE_DIS_FORCE_DOWNLOAD 如果此eFuse 设置为0(默认),软件可通过设置RTC_CNTL_FORCE_DOWNLOAD_BOOT,触发CPU 复位,将芯片启动模式强制从SPI Boot 模式切换至Download Boot 模式;如果此eFuse 设置为1,则禁用RTC_CNTL_FORCE_DOWNLOAD_BOOT。 EFUSE_DIS_DOWNLOAD_MODE ...
相反,如果EFUSE_VDD_SPI_FORCE 为 1,VDD_SPI电压取决于 eFuse(表示 flash 电压调节器是否短接至VDD_RTC_IO)。如果eFuse为0,VDD_SPI电压值为1.8V;否则为 3.3V。③ ROM日记打印控制 系统启动过程中, ROM代码日志可打印至UART和USB串口/JTAG控制器。我们可通过配置寄存器和eFuse可分别关闭UART和USB串口/JTAG...
在本章中，我们将深入探索ESP32-S3这款备受瞩目的微控制器。我们将详细阐述其定义、核心资源、功能应用...
2. 引脚配置问题：在代码中，确保已经正确设置了SPI引脚和液晶屏的控制引脚。如果引脚配置错误，可能导致...
- I can force the board in bootloader mode using reset and GPIO0 combination, and then flash a Blinky app using `idf.py app-flash`, however that seems to erase tinyuf2 I need to be able to use idf.py for uploading code - is that possible? Also, the storage functionality is not ne...
–RTC_CNTL_DG_PAD_FORCE_HOLDhold –Deep-sleepRTCIO_DIG_PAD_ HOLD_REG[n]n=0~314-8hold 52ESP32(v5.3) 4IOMUXGPIO(GPIO,IOMUX) –RTC_CNTL_DG_PAD_FORCE_HOLD RTC_CNTL_DG_PAD_FORCE_UNHOLDhold •RTC(GPIO0~GPIO17) –RTC_CNTL_HOLD_FORCE_REG[n](n=0~17)GPIO0~GPIO17RTCHold –RTC_...