圖18.配置TTL跳數 注意:TTL Hops選項用於啟用ebgp-multihop命令,該命令用於更改TTL值,以允許資料包到達非直連的外部BGP對等體或具有直連介面以外的介面。 步驟10.點選儲存並部署更改。 圖19.儲存BGP配置 步驟11.對第二個防火牆重複此過程。 圖20.配置對等體上的BGP 驗證 步驟1.驗證環回和靜態路由配置...
使用eBGP時,對等體必須直接連線。如果它們不是直接連線,則必須使用neighbor ebgp-multihop命令,並且必須存在透過IGP或靜態路由到達對等體的路徑,以便路由器建立鄰居關係。在先前的配置中,R1-AGS路由器屬於AS 300,而R6-2500路由器屬於AS 400。 使用環回地址的iBGP配置 ...
R3和R5的EBGP邻居建立步骤一样,建立EBGP邻居时重要注意一点 必须指定跳数即:neighbor4.4.4.4ebgp-multihop255否则邻居关系将建立不成功 接下来建立R2和R3的IBGP邻居 R2(config-router)#neighbornwwolfpeer-group(相当于定义一个类) R2(config-router)#neighbornwwolfremote-as1 R2(config-router)#neighbornwwolfupdate...
R3和R5的EBGP邻居建立步骤一样,建立EBGP邻居时重要注意一点 必须指定跳数即:neighbor4.4.4.4ebgp-multihop255否则邻居关系将建立不成功 接下来建立R2和R3的IBGP邻居 R2(config-router)#neighbornwwolfpeer-group(相当于定义一个类) R2(config-router)#neighbornwwolfremote-as1 R2(config-router)#neighbornwwolfupdate...
eBGP-multihop allows to loadshare through IGP between two external BGP peers (Pro). Another usage is with InterAS MBGP peering, where one option is to peer between the RR of the two AS. You have to make sure however that there are no IP routing issues like routing loops, because of ...
I would suggest you to setup the eBGP sessions using an higher multihop like 10 on both routers and also on the Palo alto devices as well. Hope to help Giuseppe 5 Helpful Reply davinci Level 1 In response to Giuseppe Larosa 08-23-2019 12:17 PM - edited 08-23-2019 12:...
在Cisco路由器里,在bgp的视图下,我终于找到这句话 ebgp-multihop 后面的解释是:允许EBGP邻居在非直连网络上。 这个就是修改默认的ttl值。 根据上文的拓扑,我们简单计算一下需要几跳。到R4为0,R3为1,R2为2,R1就是3。那么设置为3。当然也可以直接设置为255,看各位心情。
ebgp-multihop: 当配置的是EBGP对等体关系,且你的EBGP邻居和你不是直连时,要配置ebgp-multihop x(x是本地到对端设备的跳数),这个俗称EBGP的多跳。因为默认(至少cisco设备是)EBGP邻居的建立所用报文的TTL值为1,配置EBGP多跳实质上修改的是这个TTL值。(另外,IBGP邻居建立所用的报文默认的TTL值为255,所以它不...
我思科中文社区排错的全过程(多跳EBGP邻居为什么不能建立)一:基本配置:R1# interface Serial2/1 ip address12.0.0.1255.255.255.0 router bgp100 no synchroniz ation neighbor23.0.0.3remote-as200 no auto-summary R2# interface Serial2/1 ip address12.0.0.2255.255.255.0 interface Serial2/2 ip ...
4、ource LoopbackOno auto-summary!ip route 2.2.2.2 255.255.255.255 172.8.12.2/到达 R2 loopback 0 的路由,保证 TCP 可达 /2、 R2上的关键配置:router bgp 100no synchroni zati onneighbor 1.1.1.1 remote-as 200neighbor 1.1.1.1 ebgp-multihop 2/ 同上解析 /n eighbor 1.1.1.1 update-source Loop...