CONFIG_ESPTOOLPY_BEFORE="default_reset" CONFIG_ESPTOOLPY_AFTER_RESET=y # CONFIG_ESPTOOLPY_AFTER_NORESET is not set CONFIG_ESPTOOLPY_AFTER="hard_reset" # CONFIG_ESPTOOLPY_MONITOR_BAUD_CONSOLE is not set # CONFIG_ESPTOOLPY_MONITOR_BAUD_9600B is not set # CONFIG_ESPTOOLPY_MONITO...
CONFIG_ESPTOOLPY_BEFORE="default_reset" CONFIG_ESPTOOLPY_AFTER_RESET=y # CONFIG_ESPTOOLPY_AFTER_NORESET is not set CONFIG_ESPTOOLPY_AFTER="hard_reset" # CONFIG_ESPTOOLPY_MONITOR_BAUD_CONSOLE is not set # CONFIG_ESPTOOLPY_MONITOR_BAUD_9600B is not set # CONFIG_ESPTOOLPY_MONITOR_BAUD_...
CONFIG_ESP_ROM_HAS_CRC_LE=y CONFIG_ESP_ROM_HAS_CRC_BE=y CONFIG_ESP_ROM_UART_CLK_IS_XTAL=y CONFIG_ESP_ROM_USB_SERIAL_DEVICE_NUM=3 CONFIG_ESP_ROM_HAS_RETARGETABLE_LOCKING=y CONFIG_ESP_ROM_GET_CLK_FREQ=y CONFIG_ESP_ROM_HAS_HAL_WDT=y CONFIG_ESP_ROM_HAS_HAL_SYSTIMER=y ...
CONFIG_ESPTOOLPY_BEFORE_RESET=y # CONFIG_ESPTOOLPY_BEFORE_NORESET is not set CONFIG_ESPTOOLPY_BEFORE="default_reset" CONFIG_ESPTOOLPY_AFTER_RESET=y # CONFIG_ESPTOOLPY_AFTER_NORESET is not set CONFIG_ESPTOOLPY_AFTER="hard_reset" # CONFIG_ESPTOOLPY_MONITOR_BAUD_CONSOLE is not se...
CONFIG_ESPTOOLPY_BEFORE_RESET=y # CONFIG_ESPTOOLPY_BEFORE_NORESET is not set CONFIG_ESPTOOLPY_BEFORE="default_reset" CONFIG_ESPTOOLPY_AFTER_RESET=y # CONFIG_ESPTOOLPY_AFTER_NORESET is not set CONFIG_ESPTOOLPY_AFTER="hard_reset" # CONFIG_ESPTOOLPY_MONITOR_BAUD_CONSOLE is not se...
CONFIG_ESP_ROM_UART_CLK_IS_XTAL=y CONFIG_ESP_ROM_HAS_RETARGETABLE_LOCKING=y CONFIG_ESP_ROM_USB_SERIAL_DEVICE_NUM=4 CONFIG_ESP_ROM_HAS_ERASE_0_REGION_BUG=y CONFIG_ESP_ROM_GET_CLK_FREQ=y # # Boot ROM Behavior # CONFIG_BOOT_ROM_LOG_ALWAYS_ON=y # CONFIG_BOOT_ROM_LOG_...
Infact, with the "default" Configuration everything works as expected. The problem is to sent debugs on UART0 which interfere with external module. I'm going to do a test the same configuration Code: Select all CONFIG_CONSOLE_UART_DEFAULT= CONFIG_CONSOLE_UART_CUSTOM=y CONFIG_CONSOLE_UART_...
AT application for ESP32/ESP32-C2/ESP32-C3/ESP32-C6/ESP8266 - esp-at/module_config/module_esp32c3_default/sdkconfig_silence.defaults at 05ade88d9e48b32b70e095711f00f7d5ff77f47d · espressif/esp-at
两个ESP32模组能够让用户更灵活地实现并发通信功能,支持Wi-Fi、ESP-Now,Wi-Fi+BluetoothLE等通信。 ESP32可作为独立系统运行应用程序或是主机MCU的从设备,通过SPI/SDIO或I2C/UART接口提供Wi-Fi和蓝牙功能。 与纯PCB板载天线相比,外部天线扩展了网关的覆盖范围;一颗UART芯片可简化使用;WS2812B状态LED支持用户分别在...
Implementing UART driver for WiFi ESP Click Board on LPC55S28-EVK bySegFault0on11-18-202405:23 AMLatest post on11-19-202402:52 PMbyPavel_Hernandez 0 1 Possibility to add an additional code generator? byThe0on10-22-202412:31 AMLatest post on10-23-202402:04 AMbyThe0 ...