uart的配置主要是给 uart_config_t 结构体赋值,然后通过uart_param_config函数进行uart设置 以下对uart_config_t 结构体进行说明 typedefstruct{intbaud_rate;//波特率uart_word_length_tdata_bits;//数据位uart_parity_tparity;//奇偶校验位uart_stop_bits_tstop_bits;//停止位uart_hw_flowcontrol_tflow_ctrl;...
3 int uart_num = UART_NUM_0; 4 uart_config_t uart_config = { 5 .baud_rate = 115200, 6 .data_bits = UART_DATA_8_BITS, 7 .parity = UART_PARITY_DISABLE, 8 .stop_bits = UART_STOP_BITS_1, 9 .flow_ctrl = UART_HW_FLOWCTRL_DISABLE, 10 .rx_flow_ctrl_thresh = 122, 11 }; ...
UART驱动程序的函数使用uart_port_t标识每个UART控制器。以下所有函数调用都需要此标识。 设置通信参数 UART通信参数可以在单个步骤中全部配置,也可以在多个步骤中单独配置 (1)单个步骤 调用函数uart_param_config()并向其传递一个uart_config_t结构。uart_config_t结构应该包含所有必需的参数。参见下面的示例。 (2)...
调用函数uart_param_config()并传递给它一个uart_config_t结构。uart_config_t结构应该包含所有需要的参数。请看下面的例子。 const uart_port_t uart_num = UART_NUM_2; uart_config_t uart_config = { .baud_rate = 115200, .data_bits = UART_DATA_8_BITS, .parity = UART_PARITY_DISABLE, .stop_...
1.uart_config_t结构体和设置参数函数uart_param_config() 用来初始化串口使用。 /*** @brief UART configuration parameters for uart_param_config function*/typedefstruct{// 波特率intbaud_rate;/*!< UART baud rate*/// 字节长度uart_word_length_tdata_bits;/*!< UART byte size*/// 校验uart_parit...
} uart_config_t; ESP32总共有三个串口分别是UART_NUM0,UART_NUM1,UART_NUM2。串口0作为软件日志打印接口,其他串口可以为我们所用,比较灵活的是 所有串口的IO都可以自由设置。上面结构体是串口配置结构体包含了串口的波特率,数据长度,奇偶检验,停止位,硬件流控制,还有时钟源。
登录后复制voidbegin(unsignedlongbaud,uint32_tconfig=SERIAL_8N1,int8_trxPin=-1,int8_ttxPin=-1,boolinvert=false,unsignedlongtimeout_ms =20000UL);//串口初始化voidend();//失能串口voidupdateBaudRate(unsignedlongbaud);//重新设置波特率intavailable(void);//返回串口接收缓冲区中的数据intread(void)...
uart_config_t uart_config = { .baud_rate = 115200,.data_bits = UART_DATA_8_BITS,.parity =...
这里要注意参数:uart_queue属于freertos里面的队列句柄,在这里表示用于指示来自串口底层中断的队列消息。 2.2、uart参数配置 代码语言:javascript 代码运行次数:0 运行 AI代码解释 esp_err_tuart_param_config(uart_port_t uart_num,constuart_config_t*uart_config); ...
uint8_t ota_table[2] = {0x0a,0x0a}; static void UART_OTA_Task(void *arg); void UART_Init(uint32_t baud) { const uart_config_t uart_config = { .baud_rate = baud, .data_bits = UART_DATA_8_BITS, .parity = UART_PARITY_DISABLE, ...