通过配置GPIO交换矩阵,可以将UART的信号连接到指定的GPIO引脚上,例如将UART2_RX连接到GPIO33。 GPIO交换矩阵配置代码(C语言) // 配置UART引脚uart_config_tuart_config={.baud_rate=115200,.data_bits=UART_DATA_8_BITS,.parity=UART_PARITY_DISABLE,.s
typedefstruct{intbaud_rate;//波特率uart_word_length_tdata_bits;//数据位uart_parity_tparity;//奇偶校验位uart_stop_bits_tstop_bits;//停止位uart_hw_flowcontrol_tflow_ctrl;//硬件流控uint8_trx_flow_ctrl_thresh;//硬件流控的RTS阈值union{uart_sclk_tsource_clk;//时钟源booluse_ref_tick __attri...
I want to passthrough data from UART to BLE as the BLE notify enabled.Then I create a task to deal with it,at the first time, all is normal,but after I delete the task and create it again,the UART data are all "A5",and the length is 255,even I didn't sent any data to UART...
TOF10120典型测距范围为100-1800mm,电源电压3-5v,消耗电流35mA,兼容Arduino、ESP8266、ESP32等5V和3.3V控制板,适合-20°C to +70°C等室内外环境。 TOF10120支持UART、I2C通讯,1#引脚、2#引脚、3#引脚、4#引脚、5#引脚、6#引脚分别为GND、VDD、RXD、TXD、SDA、SCL。在六个引脚中,本项目只使用了其中的GN...
other types of events. If we take too much time on data event, the queue might be full.*/ case UART_DATA: uart_read_bytes(EX_UART_NUM, dtmp, event.size, portMAX_DELAY); esp_mqtt_client_publish(client, "/test/shixi", event.size, 0, 1, 0); ...
const int uart_num = UART_NUM_2;uart_config_t uart_config = { .baud_rate = 115200, .date_bits = UART_DATA_8_BITS, .parity = UART_PARITY_DISABLE, .stop_bits = UART_STOP_BITS_1, .flow_ctrl = UART_HW_FLOWCTRL_CTS_RTS, .rx_flow_ctrl_thress = 122,};// Con...
.通讯模式-uart_set_mode()从uart_mode_t中选择。 配置举例: constintuart_num =UART_NUM_2; uart_config_t uart_config={ .baud_rate=115200, .date_bits=UART_DATA_8_BITS, .parity=UART_PARITY_DISABLE, .stop_bits=UART_STOP_BITS_1,
.通讯模式-uart_set_mode()从uart_mode_t中选择。 配置举例: const int uart_num = UART_NUM_2; uart_config_t uart_config = { .baud_rate = 115200, .date_bits = UART_DATA_8_BITS, .parity = UART_PARITY_DISABLE, .stop_bits = UART_STOP_BITS_1, ...
data_bits = UART_DATA_8_BITS,//数据位8位 .parity = UART_PARITY_DISABLE,//无奇偶校验 .stop_bits = UART_STOP_BITS_1,//停止位1位 .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,//不使用硬件流控 .source_clk = UART_SCLK_APB,//串口使用的时钟 }; /*初始化串口1*/ uart_driver_install(UART_...
I have an ESP32-S2FH4 chip, USB-UART is connected to it via UART0. When trying to flash the chip, the error "A fatal error occurred: Failed to connect to ESP32-S2: No serial data received" is displayed. At the same time, the device enters the bootloader correctly, debug messages ...