将配置文件中stepper_z的position_min改为-1,保存并重启 这一步是为了让Z轴运动可以超过限位1mm,方便后面的精准调节。 2.传感器校准 还记得之前配置文档中bltouch我们不知道的offset值吗,接下来我们就来测量,找一10x10cm左右的纸,在纸的中间点一个点,复位打印机 然后移动挤出头到点的位置,记下坐标值,把bltouch...
硬件配置完成,下面打开fluidd,编辑配置文件 printer.cfg。 需要修改的地方,主要是Z轴和bltouch两处配置。 在Z轴配置 [stepper_z] 下增加bltouch配置: [bltouch] sensor_pin: ^PC4 control_pin: PB5 z_offset:2 x_offset:47.6 y_offset:5.6 pin_move_time:0.6 偏移数据需要自己测试修改。 Z轴配置修改为如...
I have the Duet WiFi and Duex5 boards. I've installed Klipper and everything works except the bl touch. The bl touch does its system check moving up and down and I have a solid red light. The debug pin down command doesn't move the pin down. Pushing the pin up or down the probe...
I'm have the same issue, except Klipper will not accept the fact that there is a SAVE_CONFIG section. In fact, I wind up with 2 SAVE_CONFIG sections, and I still get the "Option 'z_offset' in section 'bltouch' must be specified" error. Here's the relevant info. I have also at...
[printer] kinematics: cartesian max_velocity: 300 max_accel: 3000 max_z_velocity: 5 max_z_accel: 100 [bltouch] sensor_pin: ^PC4 ; P1.24 control_pin: PA4 ; P1.26 pin_up_reports_not_triggered: true pin_move_time: 0.200 x_offset: -46 y_offset: -2 z_offset: 0 speed: 5 [homing...
## More infomation at : https://www.klipper3d.org/BLTouch.html ## This bltouch is not used for Z height, only Quad Gantry Leveling ## In Z+ Position sensor_pin: PA3 ## In Y+ Position control_pin: PA2 #probe_with_touch_mode: True ...
z_offset: 1.0 activate_gcode: SET_SERVO SERVO=BFPTouch ENABLE=1 SET_SERVO SERVO=BFPTouch ANGLE=45 G4 P300 deactivate_gcode: SET_SERVO SERVO=BFPTouch ANGLE=5 SET_SERVO SERVO=BFPTouch ENABLE=0 Instructions for a skr v1.4 on my Ender3 using Klipper firmware by [Kofferkulli](kofferkulli/des...
#z_offset: 0 probe_with_touch_mode: true stow_on_each_sample: false [bed_mesh] speed: 120 mesh_min: 20, 20 mesh_max: 200, 200 probe_count: 5,5 algorithm: bicubic [safe_z_home] home_xy_position:115, 115 speed: 75 z_hop: 5 ...
I have an Ender 3 with an MKS Gen L v1.0 board fitted. I was using Marlin until yesterday with my original BL Touch happily for months. I decided to give Klipper a try and I have to say: VERY impressed! Unfortunately when trying G28 Z it gives me the error "BLTouch failed to ver...
Cancel Submit feedback Saved searches Use saved searches to filter your results more quickly Cancel Create saved search Sign in Sign up {{ message }} Toxithot / skr-no-bl-touch Public Notifications You must be signed in to change notification settings Fork 0 Star 0 ...