BL-touch配置,3D打印机调平及网床校准, 视频播放量 33647、弹幕量 13、点赞数 499、投硬币枚数 313、收藏人数 700、转发人数 142, 视频作者 三三三三三文啊, 作者简介 找不到适合自己的产品,那就DIY!合作邮箱:sevenxiaoyu920807@163.com,Q群:495187829 ,相关视频:
[printer] kinematics: cartesian max_velocity: 300 max_accel: 3000 max_z_velocity: 5 max_z_accel: 100 [bltouch] sensor_pin: ^PC4 ; P1.24 control_pin: PA4 ; P1.26 pin_up_reports_not_triggered: true pin_move_time: 0.200 x_offset: -46 y_offset: -2 z_offset: 0 speed: 5 [homing...
I have an Ender 3 with an MKS Gen L v1.0 board fitted. I was using Marlin until yesterday with my original BL Touch happily for months. I decided to give Klipper a try and I have to say: VERY impressed! Unfortunately when trying G28 Z it...
取决于你bltouch安装的高度(一般来说,探针收起时比挤出头高3mm),我们先把bltouch的z_offset设置为1。把之前注释掉的bltouch部分代码恢复,保存并重启 重启后bltouch探针会反复弹出几次,等缩回后 输入BLTOUCH_DEBUG COMMAND=pin_down,探针弹出 输入BLTOUCH_DEBUG COMMAND=pin_up,探针缩回 再次输入BLTOUCH_DEBUG CO...
I have the Duet WiFi and Duex5 boards. I've installed Klipper and everything works except the bl touch. The bl touch does its system check moving up and down and I have a solid red light. The debug pin down command doesn't move the pin down. Pushing the pin up or down the probe...
Enhanced Printhead Stability:The Eddy sensor provides robust support for Klipper and BLTouch, maintaining printhead stability. Precision 3D Touch:The 3D Touch feature offers precise leveling for optimal 3D printing accuracy and quality. User-Friendly Installation:Designed for ease of use, the Eddy senso...
Eddy Coil lacks thermal compensation and is therefore not optimized for Z-homing. It is primarily designed to work in conjunction with an existing Z-homing device such as an endstop or probe. It offers rapid bed scanning functionality when combined with an existing Z-homing device. We have mo...
I broke my BLTouch so I got a new one which is version 3.0. My old one worked fine on Ender 3 with stock board. But the new probe seems to be always in open state so homing Z doesn't work. (I added pin_up_touch_mode_reports_triggered: Fa...
BLtouch | BDsensor GND --> GND 5V --> 5V S --> CLK/SCL (Input) GND --> GND Zmin --> SDA (Input/Output) Since some of the pins in the connectors on the mainboard maybe not connected to the gpios of MCU directly (e.g. there maybe a filter capacitor on them or isolated by...
bltouch一共有5根线,其中,两根白黑色线,直接插到Z轴的插孔里,另外三根,线序按红黄绿的顺序,依次插到主板246的插孔里。 硬件配置完成,下面打开fluidd,编辑配置文件 printer.cfg。 需要修改的地方,主要是Z轴和bltouch两处配置。 在Z轴配置 [stepper_z] 下增加bltouch配置: ...