此下一 个示例与bandwidth remaining percent命令结合bandwidth percent命令明 确地控制未使用的100千位每秒带宽的分配。与此配置, 100 kbps在80:10 (8:1)比率共享在bar类和baz 之间。 policy-map foo class bar bandwidth percent 30 bandwidth remaining percent 80 class baz bandwidth percent 60 bandwidth remaini...
此下一 个示例与 bandwidth remaining percent命令结合 bandwidth percent命令明 确地控制未使用的100千位每秒带宽的分配。与此配置, 100 kbps在80:10 (8:1)比率共享在bar类和baz 之间。 policy-map foo class bar bandwidth percent 30 bandwidth remaining percent 80 class baz bandwidth percent 60 bandwidth rem...
policy-map baz class voice priority percent 10 class data bandwidth remaining percent 30 class video bandwidth remaining percent 20 policy-map poli class voice class data bandwidth 30 class video bandwidth 20 注意:这里bandwidth remaining percent 命令在Cisco IOS 版本12.2(T)后开始使用. 使用police命令设...
bandwidth percent 60 bandwidth remaining percent 10 使用police命令设置最大值 如果带宽或优先等级不应该超出其分配的带宽在周期没有拥塞,您能与police命令结合priority命令。此配置强加总是活跃的在组的一个最大速率。选择配置监控语句在此配置取决于制度的目标。 了解可用带宽值 此部分在show interface或show queueing...
带宽百分比功能如Cisco IOS软件版本12.1T和12.2所理解,在Cisco IOS软件版本12.2T和12.3中保留,并引入新命令bandwidth remaining percent。 您可以从Low Latency Queueing with Priority Percentage Support中阅读有关这些更改的详细信息。 示例如下: policy-map test123 ...
priority percent 10 class data bandwidth remaining percent 30 class video bandwidth remaining percent 20 policy-map poli class voice class data bandwidth 30 class video bandwidth 20 Note:The bandwidth remaining percent command was introduced in Cisco IOS version 12.2(T). Refer toLow Latency Queueing...
注意:这里bandwidth remaining percent 命令在Cisco IOS 版本12.2(T)后开始使用. 使用police命令设置一个最大值 如果带宽(bandwidth)或优先级(priority)类(class)在没有发生拥塞期间,未超过分配的带宽,您能够在police命令中使用priority命令。这个配置总是在一个活动的类(class)中使用了最大速率。应该选择性的根据策略...
(config-cmap)#match access-group r3(config-cmap)#policy-maptest r3(config-pmap)#class class-1 r3(config-pmap-c)#bandwidth <8-2000000>kilo bits per second percent totalbandwidth remaining remainingbandwidth r3(config-pmap-c)#bandwidth percent 50 r3(config-pmap-c)#class class-2 r3(config-...
Bandwidth statement was to allow the child service-policy to have a BW in reference when using the "bandwidth remaining percent X" command. So for example if "service-policy EMEA_Outbound_Site1" has different classes like HTTP bandwidth remainin percent 10, ms-share 5% etc etc the ...
policy-map BANDWIDTH-REMAINING class EF priority level 1 police rate percent 20 class AF11 bandwidth remaining percent 10 class AF21 bandwidth remaining percent 20 class AF31 bandwidth remaining percent 30 ! end The policy-map is exactly the same, except this time we used the bandwidth remaining...