此下一 个示例与bandwidth remaining percent命令结合bandwidth percent命令明 确地控制未使用的100千位每秒带宽的分配。与此配置, 100 kbps在80:10 (8:1)比率共享在bar类和baz 之间。 policy-map foo class bar bandwidth percent 30 bandwidth remaining percent 80 class baz bandwidth percent 60 bandwidth remaini...
此下一 个示例与 bandwidth remaining percent命令结合 bandwidth percent命令明 确地控制未使用的100千位每秒带宽的分配。与此配置, 100 kbps在80:10 (8:1)比率共享在bar类和baz 之间。 policy-map foo class bar bandwidth percent 30 bandwidth remaining percent 80 class baz bandwidth percent 60 bandwidth rem...
policy-map baz class voice priority percent 10 class data bandwidth remaining percent 30 class video bandwidth remaining percent 20 policy-map poli class voice class data bandwidth 30 class video bandwidth 20 注意:这里bandwidth remaining percent 命令在Cisco IOS 版本12.2(T)后开始使用. 使用police命令设...
策略映射中带有bandwidth percent命令的类现在具有分配给它的固定带宽计算量。所有带宽或带宽百分比、优先级和优先级百分比类的总和必须与最大保留带宽规则相符。 带宽百分比功能如Cisco IOS软件版本12.1T和12.2所理解,在Cisco IOS软件版本12.2T和12.3中保留,并引入新命令bandwidth remaini...
bandwidth remaining percent 20 policy-map poli class voice class data bandwidth 30 class video bandwidth 20 Note:The bandwidth remaining percent command was introduced in Cisco IOS version 12.2(T). Refer toLow Latency Queueing with Priority Percentage Supportfor a detailed description of thebandwidthco...
bandwidth remaining percent 80 class baz bandwidth percent 60 bandwidth remaining percent 10 使用police命令设置最大值 如果带宽或优先等级不应该超出其分配的带宽在周期没有拥塞,您能与police命令结合priority命令。此配置强加总是活跃的在组的一个最大速率。选择配置监控语句在此配置取决于制度的目标。 了解可用带...
One of the most common questions that CCIE candidates face when studying QOS MQC for the lab is “What is the difference between bandwidth percent and bandwidth remaining percent?”. Both are used in CBWFQ when implementing congestion management but what is the difference? The answer to this que...
bandwidth percent {value} 指定带宽分配作为底层链路速率的 百分比。 bandwidth remaining percent {value} 指定带宽分配作为未分配 到其他组带宽的百分比。 注意:bandwidth命令定义了一个工作情况,是最小带宽保证, 电脑资料 《比较QoS服务策略的bandwidth及priority命令》(https://www.unjs.com)。不是所有的Cisco路由器...
policy-map BANDWIDTH-REMAINING class EF priority level 1 police rate percent 20 class AF11 bandwidth remaining percent 10 class AF21 bandwidth remaining percent 20 class AF31 bandwidth remaining percent 30 ! end The policy-map is exactly the same, except this time we used the bandwidth remaining...
注意:这里bandwidth remaining percent 命令在Cisco IOS 版本12.2(T)后开始使用. 使用police命令设置一个最大值 如果带宽(bandwidth)或优先级(priority)类(class)在没有发生拥塞期间,未超过分配的带宽,您能够在police命令中使用priority命令。这个配置总是在一个活动的类(class)中使用了最大速率。应该选择性的根据策略...