第一个ZYNQ的实验,用于熟悉开发环境和板卡,通过GPIO控制LED,由于P2在ps端没有LED,所以需要通过axi总线控制PL端LED。 1、参考设计 参考的是黑金的《PL 端和 PS 端的协同设计流水灯实验 》。 2、新建工程 新建一个工程,选择zynq的FPGA,然后Create Block Design,然后右击Add ip,输入zynq,如下图所示: 然后更改里面...
使用GP AXI总线(需要配置的AXI Master,FCLK,FCLK_RESET)These interfaces are for general-purpose use only and are not intended to achieve high performance.8.1 配置,使能AXI Master总线,同时必须为AXI Master配置一个FCLK时钟,和一个FCLK_RESET复位信号。配置完成后处理器增加两个端口:M_AXI_GP0,M_ 18、...
本章讲解使用PL端以太网口实现UDP通信。开发板中实现千兆网 UDP 传输的基本逻辑框架如下图所示。FPGA 程序基于米联客的新版 UDP IP 协议栈以及 Xilinx 的 IP 核 Tri Mode Ethernet MAC 和1G/2.5G Ethernet PCS/PMA or SGMII 而实现。 本教程适用于具有PL端网口的开发板MZ7XB-7020。
DMAC 支持高达 8 个通道,所以多个 DMA 结构的核可以挂在单个DMAC 上。 DAMC 与 PL 的连接是通过 AXI_GP 接口,这个接口最高支持到 32 位宽度,这也限制了这种模式下的传输速率,理论最高速率为 600MB/s。这种模式不占用 PL 资源,但需要对 DMA 指令编程,会增加软件的复杂性。 为了获取更高的传输速率,可以以...
* The receive side will only get one completion interrupt for this example. *//*** Type Definitions ***//*** Macros (Inline Functions) Definitions ***//*** Function Prototypes ***/#ifndefDEBUGexternvoidxil_printf(constchar*format, ...);#endif#ifdefXPAR_UARTNS550_0_BASEADDRvoidUart550...
I have tried using both microsoft's SQL driver and the sourceforge SQL driver, only the sourceforge driver is working. But it will not run the Database evolution script. BUILD.SBT - When I create my d... Universal app popover in iPad version ...
如图,AXI DMA主要包括Memory Map和 Stream两部分接口,前者连接PS子系统,后者则连接带有流接口的PL IP核。 其最简单的事直接寄存器模式(Simple DMA),这里需要注意地址对齐的问题:当没有使能地址重对齐的情况下,如果AXI Memory Map数据位宽是32bit,则搬移数据所在地址必须在0x0,0x4,0x8等起始地址上。接下来关注DMA...
OCM(片上存储),L2 cache, andDDR controllerare the three main sources of sharable buffer space within the PS. The L2 cache and DDR controller provide excellent buffer-access latency for sharing data between the processor andACP(加速器链接接口)port. Only the ACP can access theL2 cache from PL...
$cd ./ zcu102-pl2ps_irq $petalinux-config --get-hw-description $petalinux-config -c kernel Enable UIO_PDRV_GENIRQ driver CONFIG_UIO=y # CONFIG_UIO_CIF is not set CONFIG_UIO_PDRV_GENIRQ=y $petalinux-build -c device-tree PL侧的dtsi文件生成与./components/plnx_workspace/device-tree-...
type == 1) { /* Down press only */ key_code = ev.code; if (key_code == KEY_DOWN) { /* lower speed */ /* Protect from concurrent read/write */ pthread_mutex_lock(&lock); if (led_speed > 0) led_speed -= 1; pthread_mutex_unlock(&lock); } else if (key_code == KEY...