Sending resync command to local computer... The command completed successfully. 4. 处理输出 如果命令执行成功,通常会看到“The command completed successfully.”的消息。如果命令失败,将显示错误消息,指示问题的原因。根据错误消息,你可能需要调整NTP服务器地址、检查网络连接或确认Windows时间服务的状态。 5. 额...
Windows 时间服务遵循网络时间协议 (NTP) 规范,该规范要求使用 UDP 端口 123 进行所有时间同步。 计算机同步其时钟或向另一台计算机提供时间时,该同步在 UDP 端口 123 上进行。 此端口由 Windows 时间服务保留为目标端口。 备注 NTP 服务器通常在 UDP 端口 123 上侦听请求,并从同一端口响应,收件箱 W32Time NTP...
Windows 时间服务遵循网络时间协议 (NTP) 规范,该规范要求使用 UDP 端口 123 进行所有时间同步。 计算机同步其时钟或向另一台计算机提供时间时,该同步在 UDP 端口 123 上进行。 此端口由 Windows 时间服务保留为目标端口。 备注 NTP 服务器通常在 UDP 端口 123 上侦听请求,并从同一端口响应,收件箱 W32Time NTP...
請勿在 Windows 時間服務執行時,使用 Net time 命令來設定電腦時鐘時間。 此外,在執行 Windows XP 或更早版本的舊型電腦上,Net time/querysntp 命令會顯示電腦所設定用來作為同步依據的網路時間通訊協定 (NTP) 伺服器名稱,但只有在電腦的時間用戶端設定為 NTP 或 AllSync 時,才會使用該 NTP 伺服器。 此命令已...
Don't use the Net time command to configure or set a computer's clock time when the Windows Time service is running. Also, on older computers that run Windows XP or earlier, the Net time /querysntp command displays the name of a Network Time Protocol (NTP)...
NTP服务的时间同步间隔默认是5分钟,您可以根据业务需求自定义同步间隔。请按以下步骤修改时间同步间隔: 单击开始图标 ,在底部单击下拉按钮,然后单击运行,在运行对话框中执行命令regedit。 在注册表编辑器的左侧目录树中,选择\HKEY_LOCAL_MACHINE\> *SYSTEM*> *CurrentControlSet*> *Services*> *W32Time*> *TimeProvid...
Windows 时间服务遵循网络时间协议 (NTP) 规范,该规范要求使用 UDP 端口 123 进行所有时间同步。 计算机同步其时钟或向另一台计算机提供时间时,该同步在 UDP 端口 123 上进行。 此端口由 Windows 时间服务保留为目标端口。备注 NTP 服务器通常在 UDP 端口 123 上侦听请求,并从同一端口响应,收件箱 W32Time ...
Windows 时间服务遵循网络时间协议 (NTP) 规范,该规范要求使用 UDP 端口 123 进行所有时间同步。 计算机同步其时钟或向另一台计算机提供时间时,该同步在 UDP 端口 123 上进行。 此端口由 Windows 时间服务保留为目标端口。 备注 NTP 服务器通常在 UDP 端口 123 上侦听请求,并从同一端口响应,收件箱 W32Time NTP...
net stop w32time w32tm/config/syncfromflags:manual/manualpeerlist:"0.it.pool.ntp.org 1.it.pool.ntp.org 2.it.pool.ntp.org 3.it.pool.ntp.org"net start w32time w32tm/config/update w32tm/resync/rediscover 1. 2. 3. 4. 5. .BAT Sample File :https://gist.github.com/thedom85/dbeb5862...
After you type the command, press ENTER. Console Copy w32tm /config /update /manualpeerlist:NTP_server_IP_Address,0x8 /syncfromflags:MANUAL Note When you use the 0x1 flag with the /manualpeerlist switch, you specify use of SpecialPollInterval . To work around this problem,...