setconf<interface> <configuration-filename> Sets the current configuration of<interface>to the contents of<configuration-filename>, which must be in the format described byConfiguration File Formatbelow. addconf<interface> <configuration-filename> ...
add-apt-repository ppa:wireguard/wireguard apt-getupdateapt-getinstall wireguard 然后就要建立服务端和客户端的私钥和公钥,由于我自己用一键脚本建立过,所以我直接把之前的/etc/wireguard/里的东西覆盖,然后输入下面命令就搞定 wg-quick up wg0 [#] iplinkadd wg0typewireguard[#] wg setconf wg0 /dev/fd/6...
kgctl showconf peer squat > peer.ini sudo wg setconf wg0 peer.iniSee the VPN docs for more details.Multi-cluster ServicesA logical application of Kilo's VPN is to connect two different Kubernetes clusters. This allows workloads running in one cluster to access services running in another. ...
When I place wg1.conf and wg2.conf in the config/wg_conf directory, I get the following: *** Activating tunnel /config/wg_confs/wg1.conf *** wireguard | [#] ip link add wg1 type wireguard wireguard | [#] wg setconf wg1 /dev/fd/63 wireguard | [#] ip -4 address add 192.16...
${WG} setconf ${config} "${wg_cfg}" @@ -297,10 +297,10 @@ proto_amneziawg_teardown() { local config="$1" proto_amneziawg_check_installed if proto_amneziawg_is_kernel_mode; then ip link del dev "${config}" >/dev/null 2>&1 else rm -f /var/run/wireguard/${config}.soc...
当我sudo wg-quick up wg0-client时,我得到: [#] wg setconf wg0-client /dev/fd/63[#] ip link set mtu 1 浏览20提问于2019-04-12得票数 7 1回答 配置持久有线网络接口 、、 手动服务器和客户端配置工作良好。10.0.0.4/8ip link set up dev wg0# interface: wg0当向/etc/网络/接口添加接口...
The configuration file will be passed directly to wg(8)'s `setconf' sub-command, with the exception of the following additions to the Interface section, which are handled by this tool: Address — a comma-separated list of IP (v4 or v6) addresses (optionally with CIDR masks) to be assign...
When I place wg1.conf and wg2.conf in the config/wg_conf directory, I get the following: *** Activating tunnel /config/wg_confs/wg1.conf *** wireguard | [#] ip link add wg1 type wireguard wireguard | [#] wg setconf wg1 /dev/fd/63 wireguard | [#] ip -4 address add 192.16...
[#] wg setconf wg0 /dev/fd/63 [#] ip -4 address add 10.66.0.9/24 dev wg0 [#] ip -6 address add 2001:470:ecd6:1::9/64 dev wg0 [#] ip link set mtu 1420 up dev wg0 [#] resolvconf -a tun.wg0 -m 0 -x /etc/resolvconf/update.d/libc:...
The configuration file will be passed directly towg(8)'s `setconf' sub-command, with the exception of the following additions to theInterfacesection, which are handled by this tool: Address — a comma-separated list of IP (v4 or v6) addresses (optionally with CIDR masks) to be assigned ...