在这个示例中,get_files *.v *.xdc命令会获取当前目录下所有以.v和.xdc结尾的文件,并将这些文件的列表写入到output.txt文件中。 验证输出文件是否已成功创建,并包含get_files命令的输出: 运行上述TCL脚本后,你可以检查output.txt文件是否已成功创建,并包含预期的文件列表。 请注意,以上示例假设你在Vivado的TCL控制...
#是获取文件集sources_1(由-of限定)内在综合阶段(由-used_in限定)使用的文件,#并将其按Vivado编译顺序排列(由-compile_order限定)get_files-compile_order sources-used_in synthesis\-of[get_filesetssources_1]#下列语句与上几乎相同get_files-compile_order sources-used_in synthesis\-of[get_files-of[get_...
def batch_convert:path = path_entry.getfile_type = file_type_entry.get if not os.path.isdir(path):messagebox.showerror("Error", "Invalid directory path")return converted_count = 0total_count = 0 for root, dirs, files in os.walk(path):for file in files:if file.endswith(file_type):...
首先,对平台命名: set_property PFM_NAME {<< span="">vendor>:<< span="">board>:<< span="">name>:<< span="">revision>} [get_files [current_bd_design].bd] set_property PFM_NAME {xilinx:zcu104:zcu104_base:1.0} [get_files [current_bd_design].bd] 完成命名后,您将看到一个新的“...
add_files -fileset constrs_1 ./Sources/top_full.xdc set_property library bftLib [ get_files [ glob ./Sources/hdl/bftLib/*.vhdl ]] 5. 添加初始化脚本 Tcl脚本在Vivado软件还可以自定义初始化脚本,添加图标,这样软件可以通过点击图标自动运行脚本,非常方便。zynq内嵌了ARM核和FPGA,在工程设计中添加ARM...
get_ipdefs *engine*xilinx.com:ip:ai_engine:2.0 在Vivado 2020.1的工程脚本里,还是使用的ai_engine 1.0。 setbCheckIPs 1if{$bCheckIPs== 1 } {setlist_check_ips"\ xilinx.com:ip:ai_engine:1.0\ xilinx.com:ip:axi_intc:4.1\ xilinx.com:ip:smartconnect:1.0\ ...
reorder_files -fileset constrs_1 -before [get_files wave_gen_timing.xdc] [get_files wave_gen_pins.xdc] 在非项目模式下,read_xdc或source命令的顺序决定了约束文件的读取顺序。 如果使用带有约束的IP内核,则会自动处理两组约束,如下所示: •不依赖于时钟的约束被分组到XDC文件中,PROCESSING_ORDER设置为...
will sort of transfer to other projects open at the same time. But the warning does not get ...
make_wrapper-files [get_files $dev_dir/project_1.srcs/sources_1/bd/design_1/design_1.bd] -top #创建壳子 add_files-norecurse $dev_dir/project_1.srcs/sources_1/bd/design_1/hdl/design_1_wrapper.v update_compile_order-fileset sources_1 ...
参考'custom_tx'包含子模块文件'D:',配置为Singular模式下的上下文合成。OOC子设计不允许在参考中使用。 解决方法: 输入指令: set_property generate_synth_checkpoint 0 [get_files fifo_generator_txc_192.xci]