mw指令 uboot下输入指令mw,会提示md的用法,memory write,即向内存中写入数据。 U-Boot-PetaLinux>mw mw-memorywrite (fill) Usage: mw[.b, .w, .l]addressvalue[count] b\w\l的意思同上,address是要写入内存的地址,value是要写入的值,count是从address开始要写入多少个数,这些都是16进制数。 示例: U-B...
然后裸机程序中uboot并不管理所有内存,内存是散的随便用的,所以如果程序员(使用uboot的人)自己不注意就可能出现自己把自己的数据给覆盖了。 (2)md就是memory display,用来显示内存中的内容。 (3)mw就是memory write,将内容写到内存中 (4)mm就是memory modify,修改内存中的某一块,说白了还是写内存(如果需要批...
md-memory display mm- memory modify (auto-incrementing address) mmc-MMC sub system mmcinfo- display MMCinfomw- memorywrite(fill) nand- NAND sub-system nboot-boot from NAND device nfs-boot image via network using NFS protocol nm-memory modify (constant address)ping-send ICMP ECHO_REQUEST to...
md - memory display mii - MII utility commands mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mw - memory write (fill) nm - memory modify (constant address) part - disk partition related commands ping - sendICMPECHO_REQUEST to network host...
mw - memory write (fill) nfs - boot image via network using NFS protocol nm - memory modify (constant address)ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables reginfo - print register information reset - Perform RESET of theCPUrun - run commands in an env...
md-memory display mm-memorymodify(auto-incrementing address)mmc-MMC子系统 mmcinfo-mmcinfo<dev num>--displayMMCinfo movi-movi-sd/mmc r/w sub systemforSMDKboard mtdparts-define flash/nand partitions mtest-simpleRAMread/write test mw-memorywrite(fill)nfs-boot image via network usingNFSprotocol ...
mw - memory write (fill) Usage: mw [.b, .w, .l] address value [count] ●第1个参数address是要写的内存地址。 ●第2个参数value是要写的值。 ●第3个可选参数count是要写单位值的数目。 15)nfs命令 nfs命令可以使用NFS网络协议通过网络启动映像。
bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image chpart - change active partition cmp - memory compare coninfo - print console devices and information ...
mw - memory write (fill) Usage: mw [.b, .w, .l] address value [count] 如将从 0x80000000 地址开始的 16 个 long 填充为 0xa0a0a0a0: md.l 80000000 a0a0a0a0 10 查看内存: 内存拷贝命令cp cp 用于将一段内存的数据拷贝到另一段内存中: ...
(所以你思考下我们为什么把uboot放在23E00000地址处)(2)md就是memory display,用来显示内存中的内容。(3)mw就是memory write,将内容写到内存中(4)mm就是memory modify,修改内存中的某一块,说白了还是写内存(如果需要批量的逐个单元的修改内存,用mm最合适)...