TIM8_TRG_COM_TIM14_IRQHandler<---要注意,定时器14也是用的这个 TIM8_CC_IRQHandler 25.2 定时器基础知识 注,不同定时支持的功能略有区别,基础定时器功能较少,TIM1和TIM8高级定时器功能多些。 TIM2和TIM5是32位定时器,其它定时器都是16位定时器。16位和32位的区别是CNT计数器范围不同,32位的范围是0 到...
TIM8_BRK_TIM12_IRQHandler <---要注意,定时器12也是用的这个 TIM8_UP_TIM13_IRQHandler <---要注意,定时器13也是用的这个 TIM8_TRG_COM_TIM14_IRQHandler <---要注意,定时器14也是用的这个 TIM8_CC_IRQHandler 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 25.2 定时器基础知识 ...
15. else if (TIMx == TIM5) __HAL_RCC_TIM5_CLK_ENABLE(); 16. else if (TIMx == TIM6) __HAL_RCC_TIM6_CLK_ENABLE(); 17. else if (TIMx == TIM7) __HAL_RCC_TIM7_CLK_ENABLE(); 18. else if (TIMx == TIM8) __HAL_RCC_TIM8_CLK_ENABLE(); 19. else if (TIMx == ...
DCDCAN1_SCE_IRQHandler; CAN1 SCE DCDEXTI9_5_IRQHandler; External Line[9:5]s DCDTIM1_BRK_TIM9_IRQHandler; TIM1 Break and TIM9 DCDTIM1_UP_TIM10_IRQHandler; TIM1 Update and TIM10 DCDTIM1_TRG_COM_TIM11_IRQHandler; TIM1 Trigger and Commutation and TIM11 DCDTIM1_CC_IRQHandler; TIM1 C...
* 函数名: TIM6_DAC_IRQHandler * 功能说明: TIM6定时中断服务程序 * 返回值: 无 ***/voidTIM6_DAC_IRQHandler(void) {if((TIM6->SR & TIM_FLAG_UPDATE) !=RESET) {/*清除标志*/TIM6->SR = ~TIM_FLAG_UPDATE;/*添加用户程序*/} } 使用定时器中断不要把中断入口函数的名字...
TIM1_Handler.Init.Prescaler=179; //预分频器,1M 的计数频率,1us 加 1. TIM1_Handler.Init.CounterMode=TIM_COUNTERMODE_UP; //向上计数器 TIM1_Handler.Init.Period=10000; //自动装载值 TIM1_Handler.Init.ClockDivision=TIM_CLOCKDIVISION_DIV1; HAL_TIM_IC_Init(&TIM1_Handler); //初始化 ...
TIM_Cmd(TIM1, ENABLE);} void TIM1_CC_IRQHandler(void){ PPM_test++;/* Clear TIM4 Capture ...
l控制寄存器1（TIMx_CR1）TIM1/TIM8的控制寄存器1描述如图22.2.1.1所示：图22.2.1.1 TIMx_CR1...
void USART6_IRQHandler(void){if (USART_GetITStatus(USART6, USART_IT_RXNE) != RESET) //判断为接收中断{USART_SendData(USART6, USART_ReceiveData(USART6)); //发送收到的数据GPIO_ResetBits(GPIOG, GPIO_Pin_6); //点亮LED,起到中断指示作用}}USART不用手动清除中断标志位: 走求问路盖 锋芒毕...
DCD TIM1_CC_IRQHandler ; TIM1 Capture Compare DCD TIM2_IRQHandler ; TIM2 DCD TIM3_IRQHandler ; TIM3 DCD TIM4_IRQHandler ; TIM4 DCD I2C1_EV_IRQHandler ; I2C1 Event DCD I2C1_ER_IRQHandler ; I2C1 Error DCD I2C2_EV_IRQHandler ; I2C2 Event ...